background image

弥 勒 浩 翔 科 技 有 限 公 司

Mile Hao Xiang Technology Co., Ltd

— 2 —

2.

Safety Instruction

1、

Surfing Area

As a Jetboard owner, please choose the proper surfing area. This

product shall only be used in waters permitted by the local
government and administrations.

2、

Collision avoidance

• The most common accident is a collision when surfing the Jetboard.
Collision can cause safety accidents and personal injury or death.
Practised surfing skill is the most effective way to avoid collisions.
• Power Jetboard has no brake. If you want to slow down and stop,
you must be prepared in advance. Slow deceleration can prevent
users falling into the water from inertance.

• If you are on a collision course, you should plan the route in

advance and avoid the collision actively.

3、

Wear a life vest

• When using the Jetboard, you need to understand the importance of
life vest and other protective equipment. You must wear a certified
lift vest any time when surfing, to ensure the personal safety.
• Choose a fit life vest with bright-colored and larger uplift
• Surfers should wear protective gears, such as diving suits, shoes,
gloves, etc.

4、

Wear a helmet

• Choose the helmet for water sports.
• In the event of a collision, the helmet can protect our head. When
surfing, always wear a certified water sports helmet.

5、

Surfing at the certain speed range that you can control

Summary of Contents for DLE106CC































Reviews: