background image

弥 勒 浩 翔 科 技 有 限 公 司

Mile Hao Xiang Technology Co., Ltd

— 28 —

12

Jetboard Storage notice

Please empty the remaining fuel in the fuel tank before storing the

Jetboard;

Powered off the Jetboard for storing.

Although the Jetboard has certain waterproof capability, but the

water residual in the engine compartment should be removed before
the Jetboard is stored. Remaining water will cause damage to the
engine and electronic components;

Wash the entire Jetboard with fresh water and dry it, keep the hatch

cover open, and store it in a dry, shade and ventilated place;

Before storing the Jetboard, please apply anti-rust spray (WD-40)

to metal parts to prevent the parts from oxidizing and rusting;

When the Jetboard has not used for a long time, charge the battery

regularly every 2 months to extend the battery life-time.

13

Warranty Terms

This product provides 1 year warranty from the date of purchase.

Spark plugs, starter motor, Spark plug cap, Exhaust pipe

connection sleeve ,carburetor, throttle handle and other consumable
parts are not covered by the warranty.

If the Jetboard is damaged by unauthorized modification, using

Non-DLE original parts or violated the standard operation, it will not
covered by the warranty.

Not using proper motor oil to the gasoline or using inferior motor

oil, causing engine damage is not covered by the warranty.

Summary of Contents for DLE106CC































Reviews: