DL4KA DIY599.com PA500 Instruction Manual Download Page 14

14 

 

GENERAL TROUBLESHOOTING 

fault description 

Possible reasons 

solution 

Unable to turn on your PA500 

power cord is not properly 
connected /or no power from 
the source 

Connect power source 
correctly to the device 

power source is not capable to 
deliver the power 

use proper power source 

internal fuse is open circuit 

Device need to be repaired 

 

 

 

 

 

 

Antenna tuning function does 
not work / tuner does not tune 

No antenna connected 

Connect a proper antenna 
usable for the operating 
frequencies of the PA500 

Antenna Tuner is configured 
into a manual-mode 

Set it to auto-mode 
Or trigger a manual tuning 
event 

Antenna is already matched 

No transmission / no 
amplification 

Device in in BYPASS Mode 

Set the device into TX Mode 

The Bandpass filter setting 
does not fit to the TX 
frequency 

Set the correct filter for the TX 
frequency to be used 

No TX-Power from the 
Transceiver, 

Check your Transceiver and 
connection 

Transceiver in SSB (no carrier) 

Check your Transceiver and 
connection 

 

When the PA500 current draw is too high (more than 15A), or a short circuit occurs, the 
internal fuse may blow. The unit will then no longer turn on. The device needs a service. 

 

 

Do not allow the maximum output power of the amplifier to exceed 40 W.  
The PA switches to bypass mode when the maximum output power is exceeded by 1 dBm 

 

 

Using the PA500 at high power levels for extended periods can lead to overheating and 
potential damage to the PA stage. 

 

AFTER-SALES SERVICE POLICY 

If this kit is bought in the European union, this product has a limited one-year warranty effective 
from the date of purchase. This warranty covers only manufacturing and parts defects. It does not 
cover damage caused by lightning, excess voltage on the power supply, accidental damage or 
purposeful damage or misuse. If the product needs warranty repair within two weeks of receiving the 
product, DIY599 will pay for the shipping both ways. After two weeks DIY599 will pay only for return 
shipping. If the product is not covered under warranty, the customer pays for shipping both ways 
plus the cost of the repair. 

Summary of Contents for DIY599.com PA500

















Reviews: