DKT Comega IPLoC D2-POM-n Quick Manual Download Page 20 | Manualshive

Page: 20 / 24

DKT Comega IPLoC D2-POM-n Quick Manual Download Page 20

IPLoC D2-POM-n - Mini Guide 2017-01-02. Ver. 1

Specifications are subject to change without notice.

DKT is not responsible for any typographical errors or wrong.

Page 20

WiFi - HT Physical Mode

IEEE 802.11H Support:

Tx Beamforming

IGMP Snooping:

Default is ”Enable”
You can choose between:
Enable and Disable

Default is ”Disable”
You can choose between:
Enable and Disable

Default is ”Enable”
You can choose between:
Enable and Disable

802.11h refers to the amendment added to the
IEEE 802.11 standard for Spectrum and Transmit
Power Management Extensions. It solves problems
like interference with satellites and radar using
the same 5 GHz frequency band

Beamforming allows an access point to effective-
ly concentrate its signal at the clients location.
This results in a better signal, SNR and potential-
ly a great throughput.

When enabled, IGMP Snooping monitors IGMP
communications among devices and optimizes

wireless multicast traffic.

IPLoC-xxxx

IPLoC-xxxx

«
...
18
19
20
21
22
...
»

Summary of Contents for IPLoC D2-POM-n

























Reviews:

No comments