manualshive.com logo in svg

DKT Comega IPLoC D2-POM-n, Quick Manual, Page: 10 / 24

Share
Download
DKT Comega IPLoC D2-POM-n Quick Manual Download Page 10

IPLoC D2-POM-n - Mini Guide 2017-01-02. Ver. 1

Specifications are subject to change without notice. 

DKT is not responsible for any typographical errors or wrong.

Page 10

The intent with the WPS is that you can push a 
paperclip to the hole for ~1sec and the IPLoC will 

allow mobile devices to connect to wifi without 

the need to enter encryption key.

The WPS has never been meant to grap settings 
from the primary router. 

So first of all you need to find the IP-address on 
the unit which it has received from the DHCP ser

-

ver. To do that, you can either look in your routers 

DHCP table or you need some software that can 
find an IP address in a Wi-Fi network. e.g. 

Android phone and Tablets

https://goo.gl/tsNaf8

iPhone and iPad

https://goo.gl/maf6rQ

Windows, Linux and Mac

https://goo.gl/ZVFvo3 

If you do a Net scan with software you will receive 
information for all the devices that are connected 
to the router. 

Look for information from vendor DKT A/S. Then 
you will find a MAC-address and that shall be the 

same as your IPLoC which is written on the unit. 

Look for the IP-address for that MAC-Address.
This is the address you need to be able to access 
your IPLoC.

Now when you have found the IP-address, connect 
to your home network, open a browser and enter 
the IP-address. The login screen will appear.

Username: root
Password: admin

Now that we are able to log on to the IPLoC unit 

will we make some change in the Wi-Fi configu

-

ration so that the unit will be integrated in the 
home network.

192.168.100.166 00:19:9f:20:06:08
DKT A/S
22 23 80

IP-Address

Vendor name

Ports

MAC-Address
(Label on IPLoC unit)

IP Address on IPLoC WiFi

Summary of Contents for IPLoC D2-POM-n

























Reviews:

No comments