How Receiver Functions
1 2
3 4
5 6
7 8
B. Set Receiver to MicroPLUS
®
Mode (Factory Set)
1.
Turn the Programming Selector to
Position B
.
2.
Press and hold Program Button until the Program LED flashes ONCE and receiver will BEEP once. Press and hold button again, LED will flash
and receiver will beep. Press and hold button a third time until LED continually flashes and beeps.
3.
The receiver now needs to have its power turned OFF, then back ON. Receiver is now in Micro
PLUS
®
mode.
The receiver comes from the factory already set in the Micro
PLUS
®
mode. If you need to change the receiver from Micro
CLIK
™ to Micro
PLUS
®
mode, follow the steps below.
CAUTION:
Changing an existing programmed receiver from Micro
CLIK
™ to Micro
PLUS
®
mode will erase
ALL
EXISTING MEMORY
that has been previously programmed in the receiver.
Verify Receiver is in
Micro
PLUS
®
mode:
After power has been turned back ON to receiver. Receiver will emit 3-flashes and beeps, this indicates Micro
PLUS
®
mode. Receiver may then emit
a long flash and beep
ONLY if
existing memory has been erased from the receiver.
FINISH
Programming Selector’s 12 functions:
1.
Learn Transmitters
2.
26-bit Weigand Programming (Factory Set)
3.
31-bit Weigand Programming
4.
30-bit Weigand Programming
5.
Match Facility Code
6.
Ignore Facility Code (Factory Set)
7.
Learn Master Transmitters (Up to 4)
8.
Low Power Mode
9.
Normal Power Mode (Factory Set)
A.
Erase ALL Memory
B.
Set Receiver to Micro
PLUS
®
Mode (Factory Set)
C.
Set Receiver to Micro
CLIK
™
Mode
D-F.
Not Used
Weigand LED’s:
Will blink
as Weigand data is being
transmitted.
Program LED:
Will flash
sequences during
programming and
flashes during normal
operation or frequency
interference.
The 8040 receiver responds to the Micro
PLUS
®
or Micro
CLIK
™ transmitter’s
“Transmitter
Code”
that is defined by
“Transmitter Button Codes” and “Facility Codes”.
For
example: an 8040 receiver can be programmed to respond to only the first button on a
multiple button Micro
PLUS
®
or Micro
CLIK
™ transmitter while a second 8040
receiver can be programmed to respond to only the second button of the same
multiple button Micro
PLUS
®
or Micro
CLIK
™ transmitter. Thus allowing a single
multiple button Micro
PLUS
®
or Micro
CLIK
™ transmitter to activate
two different
receivers
without fear of both receivers responding to the same transmitter code.
In Weigand output mode, you have the option of having the receiver
match
or
ignore
the facility code to allow the receiver to activate. One receiver can be
programmed to respond to a specific facility code while another receiver can be
programmed for a different facility code.
Program Button
Program
Selector
1
2
3
45
6
7
8
9
A
B
C
D
E
F
1
23
456
7
8
9
ABC
D
E
F
Release
Button
2 Sec.
Press and
Hold Program
Button
Press and
Hold Program
Button
Press and
Hold Program
Button
Press and
Hold Program
Button
Press and
Hold Program
Button
Press and
Hold Program
Button
START
1
23
456
7
8
9
A
B
CD
E
F
Beep
Beep
Beep
Beep
Long
Beep
Release
Button
2 Sec.
Beep
Release
Button
Receiver
power MUST be
turned OFF
then back ON
After
power has been
turned back ON
ALL Existing
Memory has
been ERASED
2 Sec.
If receiver has
existing
programming in
its memory
Beep
Micro
PLUS
®
mode
C. Set Receiver to MicroCLIK
™
Mode
1.
Turn the Programming Selector to
Position C
.
2.
Press and hold Program Button until the Program LED flashes ONCE and receiver will BEEP once. Press and hold button again, LED will flash
and receiver will beep. Press and hold button a third time until LED continually flashes and beeps.
3.
The receiver now needs to have its power turned OFF, then back ON. Receiver is now in Micro
CLIK
™
mode.
If you need to change the receiver from Micro
PLUS
®
to Micro
CLIK
™
mode, follow the steps below.
CAUTION:
Changing an existing programmed
receiver from Micro
PLUS
®
to Micro
CLIK
™
mode will erase
ALL EXISTING MEMORY
that has been previously programmed in the receiver.
Verify Receiver is in
Micro
CLIK
™
mode:
After power has been turned back ON to receiver. Receiver will emit 2-flashes and beeps, this indicates Micro
CLIK
™
mode. Receiver may then emit
a long flash and beep
ONLY if
existing memory has been erased from the receiver.
FINISH
Release
Button
2 Sec.
START
1
23
456
7
8
9
AB
C
D
E
F
Beep
Beep
Beep
Long
Beep
Release
Button
2 Sec.
Beep
Release
Button
Receiver
power MUST be
turned OFF
then back ON
After
power has been
turned back ON
ALL Existing
Memory has
been ERASED
2 Sec.
If receiver has
existing
programming in
its memory
Beep
Micro
CLIK
™
mode
