background image

IMPORTANT SAFE OPERATING PRACTICES

3. Do not overload plow capacity  by attempting to clear snow at too fast a rate.
4. Never operate this machine without good visibility or light.  Extra lighting is highly

recommended and, depending on the jurisdiction, may be required on roadways

for nighttime plowing.

5. Never operate the plow at high transport speeds   over 16 km/h (10 mph). Above

this speed, vehicle engine overheating may also occur.

6. Exercise caution , especially when operating in reverse.
7. Do not operate without wearing adequate winter outer garments.  Do not wear

jewelery, long scarves or other loose clothing which could become entangled in

moving parts. Wear footwear which will improve footing on slippery surfaces.

WARNING:  

Restrict the use of this plow to persons who read, understand and 

follow the warnings and instructions in this manual and on the machine.

WARNING:  

The warnings, cautions, and instructions detailed in this manual 

cannot cover all possible conditions and situations that occur. It must be 
understood by the operator that COMMON SENSE AND CAUTION ARE 
FACTORS that cannot be built into this product, but MUST BE SUPPLIED BY 
THE OPERATOR.

WARNING:  

DO NOT OPERATE this equipment until it has been assembled 

and set up according to the instructions in “Snowplow Assembly”. Read and 
follow all safety rules within this Instruction Manual. Failure to do may result in 
serious personal injury.

SPECIFICATIONS

z

Blade dimensions:

SUMM8826: 2.2 m wide x 66 cm high (88 inch x 26 inch)

STOR8422: 2.1 m wide x 56 cm high (84 inch x 22 inch)

RAMP8219 2.08 m wide x 48 cm high (82 inch x 19 inch)

z

Fits most light trucks and SUVs

z

Easy attachment: slides into your custom mount

z

Electric winch with wired remote control for easy up and down snow control

z

3 locking angles: to either side or straight ahead

z

Steel construction powder coated with UV-protected paint

z

Castors allow attachment and removal in seconds, plus roll-away storage

z

Comes with:

3,000 lb. wireless winch

hardened steel cutting edge

rubber 

snow deflector

polymer plow markers

skid shoes

z

ISO 

9001 certified manufacturer

z

Assembled weight :

SUMM8826: 134.26 kg (296 lb.)

STOR8422: 128.37 kg (283 lb.)

RAMP8219: 120.2 kg (265 lb.)

z

1 year warranty

Summary of Contents for RAMP8219






















Reviews: