dji NAZA-F45 Assembling And Parameters Setup Download Page 12 | Manualshive

Page: 12 / 17

background image

www.pcessflight.com

11

CHAPTER 3

ASSISTANT SOFTWARE INSTALLATION AND CONFIGURATION

SOFTWARE AND DRIVER INSTALLATION

Note: The installer in EXE format is supported on Win XP, Win7, Win8 (32 or 64 bit)

1

.

1. Please download the driver and the Assistant installation software in EXE format from www.dji.com.

2. Switch on the transmitter and then power on your autopilot system.

3. Connect your autopilot system and PC via a Micro-USB cable.

4. Open the driver installation software and follow the instructions to complete installation.

5. Run the Assistant installation software and follow the instructions to complete installation.

1

For Windows 10, a suitable driver needs to be installed following the instructions at:

https://flitetest.com/articles/dji-naza-m-windows-10

https://www.rcgroups.com/forums/showthread.php?2462912-DJI-and-Windows-10

«
...
10
11
12
13
14
...
»

Summary of Contents for NAZA-F45


















Reviews:

No comments

Related manuals for NAZA-F45

Brand: GEPRC Pages: 18

Brand: REVELL Pages: 4

Brand: REVELL Pages: 28

Brand: PowerVision Pages: 87

Brand: GearBest Pages: 12

Brand: udir/c Pages: 8

Brand: MJX Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands