manualshive.com logo in svg

Dixon DX254 / 966651201, Operator'S Manual, Page: 40 / 68

Share
Download
Dixon DX254 / 966651201 Operator'S Manual Download Page 40

maIntenanCe

40

8065-040

Release the belt tension

Deck Belt

Deck Belt Removal

Park on a level surface. Apply park brake. Lower the 
deck into the lowest cutting position.
1.  Remove foot plate and belt shields.
2.  Remove any dirt or grass that may have 

accumulated around the cutter housings and 
entire deck surface.

3.  With a ½" breaker bar and using the square 

opening in the idler arm, shift the arm counter 
clockwise to relieve the tension on the belt.

4.  Carefully roll the belt over the top of the cutter 

housing pulleys.

5.  Remove the belt guide hardware with a ½" wrench 

and set belt guide aside.

6.  Remove the belt from around the electric clutch 

on the engine shaft.

8065-046

Remove belt guide

Deck Belt Installation

NOTE: For ease in installing the deck belt, refer to the 
routing decal on the cutting deck.
1.  Place the belt around all the pulleys except the 

center spindle pulley.

2.  With a ½" breaker bar, shift the idler arm counter  

clockwise. When there is enough slack, slip the 
belt onto the center spindle pulley.

3.  Reinstall the belt guide removed in Step 5 above.

8065-047

Refer to belt routing decal

Summary of Contents for DX254 / 966651201





































































Reviews:

No comments