manualshive.com logo in svg

Dixon DX254 / 966651201, Operator'S Manual, Page: 20 / 68

Share
Download
Dixon DX254 / 966651201 Operator'S Manual Download Page 20

ContRols

20

Tracking Knob

If the mower is not tracking straight, check the 
air pressure in both rear tires. Recommended air 
pressure for the rear tires is 15 psi (1 bar).
1.  Tracking adjustments are made using the tracking 

bolts. The tracking bolts act as limiting devices for 
the motion control levers when in the full-forward 
position.

2.  For preliminary tracking adjustment, move unit 

to an open, unobstructed area such as an empty 
parking lot or open field.

3.  Back the tracking bolts out until flush with nut.
4.  Test operate unit by driving it at full throttle and 

the full forward position on both motion control 
levers. Gradually turn in the right hand tracking 
bolt until the unit noticeably starts drifting right.

5.  Drive forward at full throttle with both motion 

control levers in the full forward position. 
Gradually turn in the left tracking until unit tracks 
straight.

Hour Meter

The hour meter displays the total operating time.
It will flash CHG OIL (Change Oil) at 50 hour intervals. 
The flash duration is one hour before and one hour 
after the interval. The CHG OIL icon will come on 
and shut off automatically. The hour meter cannot be 
manually reset.

8050-601

Hour meter

8050-230

Tracking adjustment

Summary of Contents for DX254 / 966651201





































































Reviews:

No comments