Divesoft HE/02 Manual Download Page 23 | Manualshive

Page: 23 / 31

background image

22

10. Charging and battery status

At any time when the analyzer is turned on, you can check the battery status by
pressing

. The value of the battery charge expresses double line at the bottom of display.

Range is defined between 0 to 100% charging.

When the battery is close to discharged, connect the charger to power-supply connector.

When the charger is connected, you can check the status of charge press

. If the battery

is not fully charged, the row of arrows is displayed on a scale from 0 to 100%. If it is already
charged, a long double line is displayed.

All features of the analyzer are available during charging.

«
...
21
22
23
24
25
...
»

Summary of Contents for HE/02
































Reviews:

No comments

Related manuals for HE/02

NUFLO Scanner 2000 microEFM

Brand: Cameron Pages: 8

Brand: Larson Davis Pages: 536

Brand: KBR Pages: 12

Brand: Yamaha Pages: 8

Brand: ESP Pages: 12

Brand: Seben Pages: 16

International 2S Pro

Brand: Brantz Pages: 2

Brand: Salutron Pages: 2

Multifunction Compensator

Brand: Halcyon Pages: 20

LaserRange-Master i5

Brand: LaserLine Pages: 68

Brand: Omega Pages: 4

Brand: Cewe Pages: 8

Brand: Haltech Pages: 20

Brand: Oakton Pages: 8

Brand: H&B Pages: 45

PCE-4 EKIT Series

Brand: PCE Instruments Pages: 16

Brand: WPI Pages: 32

Brand: Benstone Pages: 77

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands