background image

IP2373EN

ASSA ABLOY Entrance Systems AB

Lodjursgatan 10 
SE-261 44, Landskrona
Sweden
© ASSA ABLOY

6. Troubleshooting

Problem

Possible cause

Operation

The gate doesn’t
open or close.

No power supply.

Make sure the mains supply is active.

Gearmotor released.

See the release instructions.

Photocells occupied.

Check the photocells are clean and op-
erating correctly.

Permanent STOP command.

Check the STOP command or the con-
trol panel.

Faulty selector.

Check the selector or control panel.

Faulty remote control.

Check the condition of the batteries.

Electric lock not working.

Check the lock is positioned and work-
ing correctly.

Il cancello apre ma 
non chiude.

Photocells occupied.

Check the photocells are clean and op-
erating correctly.

7. Disposal

The packaging components (cardboard, plastic, etc.) must be separated out for recycling.
Refer to the local disposal regulations before proceeding.

The packaging materials must not be discarded in the environment or left within reach of
children, as they are a potential source of danger.

All the rights concerning this material are the exclusive property of ASSA ABLOY Entrance Systems AB.
Although the contents of this publication have been drawn up with the greatest care, ASSA ABLOY Entrance 
Systems AB cannot be held responsible in any way for any damage caused by mistakes or omissions. We 
reserve the right to make changes without prior notice. 
Copying, scanning or changing in any way is expressly forbidden unless authorised in writing by ASSA ABLOY 
Entrance Systems AB.

The crossed-out wheeled bin symbol indicates that the product should be disposed of separately from 
household waste. The product should be handed in for recycling in accordance with local environmental 
regulations for waste disposal. By separating a marked item from household waste, you will help reduce 
the volume of waste sent to incinerators or landfill and minimize any potential negative impact on human 

health and the environment.

Summary of Contents for TS35















Reviews: