background image

13. If you think that there is a problem

Will not power on

Battery low level……Please charge.

Charging does not start (the lamp does not turn red)

Charger cable missing plug……Please check the insertion of the connector on each 

  cable.

False recognition of remaining battery power……Please use the battery until the power 

  indicator goes out, and try again.

Does not run

Key is OFF……Please select one of the positions "GREEN" ,"BLUE" ,"RED".

Check motor cable……Please check that there are no missing or insufficient plug in.

After  confirming  the  above  items,  if  the  symptoms  are  not  improved,  the 
equipment may be faulty. If you repair it incorrectly, it may ignite or generate 
excessive heat because this being a lithium-ion-battery loaded device. Do not 
disassemble or repair the inside of the equipment yourself. Please contact your 
dealer or us.

No speed

Lack of tire pressure……Please add air to the recommended tire pressure.

Dragging of brake…   Please adjust the brake so that the tire turns smoothly.

Check throttle……     Please check inside of throttle for objects, crack etc. It may be  

                                    interfering with the operation.

16

Summary of Contents for Yotsuba Moto Meow 12





















Reviews: