15
GB
5 Maintenance
5.3
Cleaning the exhaust filter
1.
Switch off the appliance,
Z
Chapter 4.3, ‘Switching off’
.
2.
Push down the release catch of the exhaust filter cover and fold down
the cover (Fig. 13/A).
3.
Separate the exhaust filter from the exhaust filter cover (Fig. 13/B).
4.
Rinse the exhaust filter thoroughly by hand under clear running cold or
hand-warm water.
5.
If the filter is damaged or deformed, replace it (ordering information
Z
Chapter 5.4, ‘Spare parts and accessories’
).
6.
Insert the new/cleaned exhaust filter back into the exhaust filter cover
(Fig. 13/B). Ensure that its bulges engage with the bulges of the cover.
7.
Fit the exhaust filter cover on the bottom side first (Fig. 14/A) and then
push it back into its console (Fig. 14/B). It is easier if you push down the
release button when doing so.
8.
Check the exhaust cover is securely in place.
5.4
Spare parts and accessories
Contact:
Z
Page 48, ‘International Service’
Further information:
Z
www.dirtdevil.de
5.5
Recommendation
We recommend:
Swirl
£
Y05 dust filter bags with MicroPor
£
filtration
Swirl
, MicroPor
and ‘Y05’ are registered trade marks of a company of the Melitta group and used with their permission.
5.6
Before you send in the appliance
Before contacting your authorised Royal dealer, Royal service partner or
appliance market or before sending in the appliance, first follow the proce-
dure in the table to check if you can solve the problem yourself.
B
A
13
B
A
14
ATTENTION:
The filters are washable, but not suitable for cleaning in washing
machines or dishwashers. Do not use cleaning agents for cleaning.
Leave the filters to dry after cleaning them with water (approx. 24 hours
at room temperature). Only put them back into the appliance when they
are completely dry.
ATTENTION:
Only use original spare parts from the scope of delivery or those that you
have purchased by reordering.
Item number
Description
7010022
Set of 5 dust filter bags and 1 motor protection filter
7009002
1 exhaust filter
7009018
1 telescopic tube extension
7020008
Accessory set consisting of: Accessory holder, Uphol-
stery nozzle, Furniture brush, Crevice nozzle
M203
1 parquet brush
M209
1 turbo brush
M219
1 mini turbo brush
NOTE:
Insert the bag in direction ‘A’.
WARNING:
Danger of injury! Never use a defective appliance! Always switch off the
appliance and disconnect it from the mains before starting troubleshoot-
ing
Z
Chapter 4.3, ‘Switching off’
.
Problem
Possible cause / solution
Filter bag
change indi-
cator (Fig. 1/
16) appears
in the display
window.
The dust filter bag is full.
Change the dust filter bag
Z
Chapter 5.1, ‘Changing the
dust filter bag’
.
Nozzle, telescopic tube or suction hose is blocked.
Remove the obstacle. If necessary, use a long wooden
stick (e.g. a broomstick) to do this.
The filters are dirty.
Clean the respective filter
Z
Chapter 5.2, ‘Cleaning the
motor protection filter’
or
Z
Chapter 5.3, ‘Cleaning the ex-
haust filter’
.
The vacuum
cleaner stops
suddenly.
The overheating protection has tripped (possibly due to
blocked suction channels, filters, or similar). Switch the
appliance off and pull the plug out of the socket. Remove
the cause of overheating (e.g. by disassembling tele-
scopic tube and suction hose and removing the obstacle
and/or cleaning filters). Wait for about 45 minutes. After
the appliance has cooled off, you may switch it on again.
The cleaning
results are
unsatisfacto-
ry in spite of
the appli-
ance work-
ing correctly.
The bypass vent (Fig. 1/24) is open.
Close the bypass vent (Fig. 1/24).
The attached nozzle is unsuitable.
Change the nozzle,
Z
Chapter 3.2, ‘Assembly’
.
The position of the ‘carpet/hard floor’ selector (Fig. 1/28)
is unsuitable.
Set the "carpet/hard floor" selector (Fig. 1/28) to the cor-
rect position for the type of floor,
Z
Chapter 4.2, ‘Vacuum
cleaning’
, step 5.
The dust filter bag is full.
Change the dust filter bag
Z
Chapter 5.1, ‘Changing the
dust filter bag’
.
The filters are dirty.
Clean the respective filter
Z
Chapter 5.2, ‘Cleaning the
motor protection filter’
or
Z
Chapter 5.3, ‘Cleaning the ex-
haust filter’
.
Nozzle, telescopic tube or suction hose is blocked.
Remove the obstacle. If necessary, use a long wooden
stick (e.g. a broomstick) to do this.
NOTE:
If you cannot solve the problem following these instructions, contact the
Royal Appliance customer service (
Z
Page 48, ‘International Service’
).
Problem
Possible cause / solution
Paroly.book Seite 15 Montag, 15. August 2011 5:58 17
