background image

 Warning 

BASIC SAFETY PRECAUTIONS

• This carpet washer is intended for 

household use only and NOT for 

commercial or industrial use.

• Only use the carpet washer 

indoors and keep the area you’re 

cleaning well lit.

• Keep fingers, hair and loose 

clothing from moving parts and 

openings whilst using the carpet 

washer.

• This carpet washer is NOT to be 

used by children under eight years 

or persons with reduced physical, 

sensory or mental capabilities, 

unless they have been given 

instructions on how to use the 

machine or are supervised 

  during use. 

• Any cleaning or maintenance of 

your carpet washer should not 

be made by children without 

supervision and ensure they don’t 

play with the carpet washer.

• Before using your carpet washer 

test your carpets/rugs/upholstery 

for colourfastness and pile 

distortion.

• Only Dirt Devil recommended 

tools and solutions should be used 

with this carpet washer. Using 

other solutions may invalidate the 

guarantee.

•  Don’t leave the carpet washer  

  plugged in when unattended.

• Don’t use this carpet washer if it 

has been dropped, damaged or left 

outdoors.

•  Don’t run over the power cord or 

use carpet washer if the power 

cord or plug is damaged. Please 

contact our Customer Care Line 

on: 0330 026 2626 (Mon-Fri 

09:00-5:00).

•  Don’t use your carpet washer 

to pick up any flammable or 

combustible materials (lighter 

fluid, petrol, kerosene etc.) or use 

the carpet washer in an area with 

explosive vapours or liquid.

•  Don’t handle the plug or use the 

carpet washer with wet hands.

•  Don’t carry the carpet washer while 

it’s switched on.

•  Don’t pull or carry this carpet 

washer by the power cord.  

• Don’t use the power cord as a 

handle, pull the power cord around 

corners, sharp edges or close a 

door over the power cord.

• Don’t unplug carpet washer by 

pulling on the power cord.

• Don’t attempt to remove blockages 

with sharp objects as this may 

cause damage to your carpet 

washer.

DON’TS

Summary of Contents for LET'S GO. DDW02-E01





















Reviews: