DirecTV Advanced Installation Meter 2 Operation Manual Download Page 105

Page: 105 / 108

Page 105

AIM 2 Operation Manual

www.trilithic.com

Updating the Meter

Chapter 10

Overview

You can update your AIM as new features become available via the Internet or USB flash

drive.

You can update the meter firmware without plugging the AIM into a power outlet, as long as

the battery icon on the display shows at least two remaining bars of power. If the battery icon

shows less than two bars of power, the meter must be plugged into a power outlet using the

AC power adapter.
To view the current AIM firmware version, press

CONFIG

to go to the

CONFIGURATION

screen. Then highlight

Firmware Versions

and press

SELECT

Updating the Firmware

1. Press

CONFIG

to go to the

CONFIGURATION

screen.

2. Select

Firmware Upgrade

and press

SELECT

to go to the

FIRMWARE UPGRADE

screen.

3. The

FIRMWARE UPGRADE

screens appears

with the following options:

• Select update from the Internet
• Select update from USB

Summary of Contents for Advanced Installation Meter 2













































































































Search results

Summary of Contents for Advanced Installation Meter 2

Reviews:

Related manuals for Advanced Installation Meter 2

Brands by name

Popular brands

DirecTV Advanced Installation Meter 2, Operation Manual

Search results

Summary of Contents for Advanced Installation Meter 2

Reviews:

Related manuals for Advanced Installation Meter 2

Brands by name

Popular brands