Directed DIRECTECHS HK14 Installation Manual Download Page 3

Warning! Safety first

The following safety warnings must be observed at all times:

•  Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer.
•  When properly installed, this system can start the vehicle via a command signal from the remote control.  Therefore, never 

operate the system in an area that does not have adequate ventilation. 

The following precautions are the sole responsibility of the user; however, authorized Directed dealers should:
•  Never use a test light or logic probe when installing this unit. Always use a multimeter. 
•  Never operate the system in an enclosed or partially enclosed area without ventilation (such as a garage). 
•  When parking in an enclosed or partially enclosed area or when having the vehicle serviced, the remote start system must 

be disabled using the installed toggle switch. It is the user’s sole responsibility to properly handle and keep out of reach from 
children all remote controls to assure that the system does not unintentionally remote start the vehicle.

•  USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT TO THE VEHICLE. 

ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE 
STORAGE AREA MUST REMAIN CLOSED AT ALL TIMES.

Use of this product in a manner contrary to its intended mode of operation may result in property damage, personal injury, or 
death. Except when performing the Safety Check outlined in this installation guide, (1) Never remotely start the vehicle with 
the vehicle in gear, and (2) Never remotely start the vehicle with the keys in the ignition. The user is responsible for having the 
neutral safety feature of the vehicle periodically checked, wherein the vehicle must not remotely start while the car is in gear. 
This testing should be performed by an authorized Directed dealer in accordance with the Safety Check outlined in this product 
installation guide. If the vehicle starts in gear, cease remote start operation immediately and consult with the user to fix the problem 
immediately.

OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN GEAR IS CONTRARY TO ITS INTENDED MODE OF 
OPERATION. OPERATING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RESULT IN PROPERTY DAMAGE 
OR PERSONAL INJURY. IMMEDIATELY CEASE THE USE OF THE UNIT AND REPAIR OR DISCONNECT THE INSTALLED REMOTE 
START MODULE. DIRECTED WILL NOT BE HELD RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTALLATION COSTS.

Remote starters for manual transmission pose significant risks if not properly installed and operated. When testing to ensure the 
installation is working properly, only remote start the vehicle in neutral gear, on a flat surface and with a functional, fully engaged 
parking brake. Do not allow anyone to stand in front of or behind the vehicle. 

This product should not be installed in any convertible vehicles, soft or hard top with a manual transmission. Installation in such 
vehicles may pose certain risk.

3

Directed Digital Solutions HK14

© 2019-11-15 Directed. All rights reserved.

Summary of Contents for DIRECTECHS HK14




















Reviews: