background image

©

2005 

Directed Electronics, Inc. all rights reserved

17

System Features Menus

Menu #1 - Basic Features

Items in bold text have been programmed to the default setting at the factory.

Menu #2 - Advanced Features

Feature 

One Chirp  

Two-Chirp  

Number

Setting Setting

2-1

Siren

Horn honk

2-2

30-second siren duration

60-second siren duration

*

2-3

Nuisance Prevention

®

Circuitry ON

Nuisance Prevention

®

Circuitry OFF

2-4

Progressive door trigger

Instant door trigger

2-5

Valet switch input: 1 pulse

Valet switch input: 2-5 pulses

2-6

Bypass Notification ON 

Bypass Notification OFF

2-7

Ignition-controlled domelight ON

Ignition-controlled domelight OFF

2-8

Single unlock pulse

Double unlock pulse

2-9

Single lock pulse

Double lock pulse

2-10

Channel 3: Validity

Channel 3: latched/latched, reset 
with ignition/30-second timed/
second unlock output

*

2-11

Comfort Closure (On) (20 sec.)

Comfort Closure (Off)

*Second unlock is only available if Feature 2-8 is programmed to single pulse.

Feature 

One Chirp  

Two-Chirp  

Number

Setting

Setting

1-1

Active arming

Passive arming

1-2

Chirps ON

Chirps OFF

1-3

Ignition controlled door locks ON

Ignition controlled door locks OFF

1-4

Active locking only 

Passive locking

1-5

Panic with ignition on

No Panic with ignition on

1-6

0.8 second door lock pulses

3.5 second door lock pulses/0.4 sec.

1-7

Forced passive arming ON

Forced passive arming OFF

1-8

Automatic Engine Disable ON

Automatic Engine Disable OFF

1-9

Armed When Driving (AWD) 

Vehicle Recovery System (VRS)

1-10

Code Hopping

ON

Code Hopping

OFF

Summary of Contents for Viper 350HV






























Reviews: