background image

14

© 2011 Directed Electronics. All rights reserved.

2.  Before Unlock: the OEM Alarm Disarm wire will pulse as programmed before the unlock wire

3.  Remote start only: the OEM Alarm Disarm wire will pulse as programmed during remote start only

7.  OEM Alarm Disarm Pulses (H2/4 wire)

1.  1: the OEM Alarm Disarm wire will pulse once per operation

2.  2: the OEM Alarm Disarm wire will pulse twice per operation

 

8.  Aux 1 Output Type (H2/4 wire)

1.  Validity: when the Aux command is received the wire will turn on and remain on until the command 

ceases

2.  Latch: when the Aux command is received the wire will turn on and remain on until the command is 

received again

3.  Latch/reset/Ignition: when the Aux command is received the wire will turn on and remain on until the 

command is received again or the ignition is turned on/off

4.  Timed: when the Aux command is received the wire will turn on for the programmed time duration 

(default 30sec)

5.  Off: the output will not activate for a remote control command, use this option when the Aux com-

mand controls an external device such as a garage door module

6.  2nd unlock: the wire will operate as 2nd unlock and will not activate for remote control commands

9.  Aux 1 Linking 

1.  No Linking: the Aux output will not activate for a remote control command 

2.  Link to Lock: the Aux output will activate for the Lock command

3.  Link to Unlock: the Aux output will activate for the Unlock command

4.  Link to Lock/Unlock: the Aux output will activate for the Lock & Unlock commands

5.  Link to Remote Start: the Aux output will activate for any Remote Start activation

10. Aux 2 Output Type

• 

Refer to Aux 1 Output Type descriptions

11. Aux 2 Linking 

• 

Refer to Aux 1 Linking descriptions

12. Aux 3 Output Type

• 

Refer to Aux 1 Output Type descriptions

13. Aux 3 Linking 

• 

Options 1-4: Refer to Aux 1 Linking descriptions 

• 

Option 5: SmartKey Control (Link to Remote Start Off): The Aux output will pulse once following 

Remote Start shut down for vehicles with push button engine stop operations.  During runtime, if any 

door is opened remote start will shut down immediately and pulse the output.

14. Aux 4 Output Type

• 

Refer to Aux 1 Output Type descriptions

15. Aux 4 Linking 

• 

Refer to Aux 1 Linking descriptions

16. Aux/Trunk Output Type

• 

Refer to Aux 1 Output Type descriptions 

Summary of Contents for Clifford 410.4X






















Reviews: