DIODE LED AlphaTECH LED STRIP LIGHT Installation Manual Download Page 8

8 OF 8

®

Toll Free: 877.817.6028 | Fax: 415.592.1596 | www.DiodeLED.com | [email protected]

© 2020 Elemental LED Inc. All rights reserved. Specifications are subject to change without notice.

IG121620-3.0

AlphaTECH

®

 LED Strip Light

 INSTALLATION GUIDE

AlphaTECH

® 

LED STRIP LIGHT

INSTALLATION GUIDE

Wire 

Gauge

10 W

.42 A

20 W

.83 A

30 W

1.3 A

40 W

1.7 A

50 W

2.1 A

60 W

2.5 A

22 AWG

53 ft.

27 ft.

17 ft.

13 ft.

11 ft.

9 ft.

18 AWG

134 ft.

68 ft.

45 ft.

33 ft.

27 ft. 

22 ft. 

16 AWG

215 ft.

109 ft.

72 ft.

54 ft.

43 ft.

36 ft.

14 AWG

345 ft. 

174 ft.

115 ft.

86 ft. 

69 ft.

57 ft.

12 AWG

539 ft.

272 ft.

181 ft.

135 ft.

108 ft. 

90 ft.

10 AWG

784 ft.

397 ft.

263 ft.

197 ft.

158 ft.

131 ft.

Wire 

Gauge

10 W

.42 A

20 W

.83 A

30 W

1.3 A

40 W

1.7 A

50 W

2.1 A

60 W

2.5 A

70 W

2.9 A

80 W

3.3 A

100 W

4. 2 A

22 AWG

53 ft.

27 ft.

17 ft.

13 ft.

11 ft.

9 ft.

8 ft.

7 ft.

6 ft.

18 AWG

134 ft.

68 ft.

45 ft.

33 ft.

27 ft. 

22 ft. 

19 ft.

17 ft.

14 ft.

16 AWG

215 ft.

109 ft.

72 ft.

54 ft.

43 ft.

36 ft.

31 ft.

27 ft.

22 ft.

14 AWG

345 ft. 

174 ft.

115 ft.

86 ft. 

69 ft.

57 ft.

49 ft.

43 ft. 

36 ft.

12 AWG

539 ft.

272 ft.

181 ft.

135 ft.

108 ft. 

90 ft.

77 ft.

68 ft.

56 ft.

10 AWG

784 ft.

397 ft.

263 ft.

197 ft.

158 ft.

131 ft.

112 ft.

98 ft.

82 ft.

24V Voltage Drop & Wire Length Distance Chart

Example: 24V Voltage Drop & Wire Length Distance Chart 

Determine load size. Let’s assume 

load is 55 W. Round up to nearest 

load.

1

Determine distance from driver 

to load. Let’s assume the 

distance is 90 ft.

2

It is recommended to install 12 AWG to 

eliminate excess voltage drop.

3

VOLTAGE DROP CHARTS

For best performance and lumen output, ensure proper wire gauge is installed to compensate for voltage drop of low voltage circuits. 

Summary of Contents for AlphaTECH LED STRIP LIGHT









Reviews: