background image

12

3)  Turn the ENCODER KNOB (E) until the DISPLAY shows the 

PRINCIPAL welding CURRENT VALUE at which you wish to 
weld, in relation to the diameter of the electrode you are us-
ing.

 

The following functions are pre-set automatically in the facto-
ry:

• 

HOT START -

 Increases the welding current automatical-

ly at the start of the welding process, thereby reducing the 
risk of poor melting of the electrode at the start of the joint.

• 

ARC FORCE -

 Automatically regulates the dynamic char-

acteristics of the arc.

4)  Once the all the selections/regulations indicated above have 

been made, welding can begin.

5)  During the welding process the DISPLAY (D) shows the real 

Amps (A) at which the operator is actually welding.

  TIG welding

1)  Start the welding machine by turning the power supply switch 

to position 

I

.

2)  Press the WELDING PROCESS SELECTION Key (T2) and 

select:

 

 L1 

 a TIG “HF” welding process for direct current TIG weld-

ing with high frequency ignition.

 

 L2 

 a TIG “Lift” welding process for direct current TIG “Lift” 

type welding without high frequency.

T2

L1

L2

WARNING: The “Lift” ignition current is created by pushing 
the torch button only after having touched the workpiece with 
the electrode.

3)  Press the WELDING MODE SELECTION Key (T1) and go to 

one of the 

3

 options available:

 

 L4 

 2T

 

 L5 

 4T

 

 L6 

 SPOT WELD

T1

L5

L6

L4

4)  Turn the ENCODER KNOB (E) until the DISPLAY (D) shows 

the CURRENT VALUE at which you wish to weld.

5)  By pushing the WELDING PARAMETERS SELECTION (T3) 

key a number of times it is possible to set the various TIG 
WELDING PARAMETERS (see the “TIG Welding” paragraph 
- WELDING PARAMETERS).

T3

6)  To exit welding parameter programming, hold the T3 button 

down for about 1 second.

7)  Once the all the selections/regulations indicated above have 

been made, welding can begin.

8)  During the welding process the DISPLAY shows the real Amps 

(A) at which the operator is actually welding.

  TIG welding with the SPOT 

WELDING function on

1)  Start the welding machine by turning the power supply switch 

to position 

I

.

2)  Press the WELDING PROCESS SELECTION Key (T2) and 

select one of the welding machine’s 

2

 TIG processes:

 

 L1 

 TIG with HF ignition

 

 L2 

 TIG with “Lift” type ignition

T2

L1

L2

3)  Press the WELDING MODE SELECTION Key (T1) and go to 

one of the 

SPOT WELDING

 function.

4)  Press and release the WELDING PARAMETERS SELECTION 

Key (T3) until the SPOT WELD LED starts flashing.

5)  Rotate the ENCODER knob (E) to set the SPOT WELDING 

time required (0,1÷10,0 sec).

Summary of Contents for DIX TIG GO 1406.M HF















Reviews: