manualshive.com logo in svg

Dimplex Revillusion RBF30, Service Manual

Share
Download
Dimplex Revillusion RBF30 Service Manual Download Page 3

3

OPERATION

 

Touch Panel and Remote Controls

 WARNING:

  The Revillusion

TM

 Built-in Electric Firebox must be installed properly before it is used.

 CAUTION:

  Except for installation and cleaning described in this manual, an authorized service representative should 

perform any other servicing.
The manual controls for the Revillusion

TM

 Built-in Electric Firebox are located on the front panel. Touch an icon to activate. 

The selected setting displays on the left side of the panel. 
A multi-function remote control also is provided. The remote control has a range of approximately 30 ft (9 m). To operate 

correctly, the remote control must be pointed toward the front of the built-in electric firebox.

Icon

Function

Description

A

Power/

Standby

Press to activate the current standby state (On/Off). 

• 

Standby State On

 

Press to turn everything Off. Press again to activate the previous state.

• 

Standby State Off 

Press to activate the previous state.

 -

If the flame effect was On, the previous heat setting will be activated (On or Off). 

 -

If the flame effect was Off, the previous heat setting will be activated (High or Low).

Press again to turn everything Off.

B

Heat

• 

Heat On

 

Press to turn heat On (indicated by 1 short beep and the icon appearing on the display). 

Displays current heater temperature setting. Use the Temp Up/Down icon to change the 

heater temperature setting. 

• 

Heat Off

 

Press to turn heat Off (indicated by 1 short beep).

!

NOTE:  

After the heater is switched off, the fan will continue on for 60 seconds before 

turning off.

C

Temp Down

Press multiple times to lower the heater temperature in 1

0

 F (1

0

 C) increments. Displays 

current temperature; lowest temperature is 41

0

 F (5

0

 C). This feature is active whenever 

the heat is enabled. 

D

Temp Up

Press multiple time to raise the heater temperature in 1

0

 F (1

0

 C) increments. Displays 

current temperature; highest temperature is 99

0

 F (37

0

 C). This feature is active whenever 

the heat is enabled. 

Change Fahrenheit (

0

 F)

 to 

Celsius (

0

 C)

Press both Temp+ (

) and Temp–  (

) on the unit.

H

 

A

C

I

E

J

B

F

G

D

Figure 1

Figure 3

Summary of Contents for Revillusion RBF30

















Reviews:

No comments

Brands by name

Popular brands

Load more brands