IMPORTANT
Remember to observe all safety warnings when operating the heater on auto
setting unattended or attended
The timer allows you to select ‘
MANUAL ON
’ , ‘
AUTO
’ or’
MANUAL OFF
’ operation mode by
pressing the
‘
MODE’
(Input/Output) button until the required mode appears at the bottom of
the timer display.
‘MANUAL ON’
mode allows power to the heater uninterrupted by the timer settings. The
heat selector switch will control the output (see ‘Using the heater’).
‘
AUTO’
mode allows the convector to switch ON and OFF according to the timer settings
(see ‘Setting Programs’ section below).
‘MANUAL OFF’
mode switches off all heater operation completely.
12/24 Hour Mode
Either 12 or 24 hour modes can be used.
Press the
S
(Set) and
PROG
(Program) buttons simultaneously to switch between 12 and
24 Hour mode.
Electronic Timer Operation
Fig. 4
3
.
Now set the time by pressing the
H
(Hour) button and then
M
(Minute) button until the desired time setting is displayed.
4.
Press the
PROG
(Program) button again to finish the first ON setting and enter into the first OFF setting. By repeating steps ‘2’ & ‘3’ above
you can now complete the input of the first OFF setting.
5.
Press the
PROG
(Program) button again to finish the first ON/OFF program and enter into the 2
nd
ON setting. Repeat steps ‘2’ , ‘3’ and ‘4’
to complete this program , then press P again and repeat cycle as necessary.
6.
Once you have completed the number of ON/OFF programs you require (up to a maximum of 8) , press the
S
(Set) button to save the
settings and the timer is now ready to operate in Auto mode .
Example
: To set Timer ON at 18:15 and Timer OFF at 22:15 everyday
a)
Press
PROG
and LCD displays
‘
1_ON
’
b)
Press
D
until LCD displays
‘
MO, TU, WE, TH, FR, SA, SU
’
c)
Press
H
until LCD displays
‘
6:00PM’ or ’18:00’
d)
Press
M
until LCD displays
‘
6:15PM’ or ’18:15’
e)
Press
PROG
and LCD displays
‘
1_OFF’
f)
Repeat c) and d) until LCD displays
‘
10:15PM or 22:15
’
g)
Press
S
and the program is saved and the current time display returns.
TIP : When verifying your programs ensure that the settings do not overlap, especially when using the block option.
TIP : To clear a section in a Program, press the
C
(Clear) button. To reactivate this section press the
C
button again.
Notes on switching between Manual ON/Auto/Manual OFF
1.
Pressing
MODE
(Input/Output) button allows you to change between
Manual ON / Auto / Manual OFF
modes , current mode will be displayed on the bottom of the LCD display
.
2.
In
Manual ON
or
Manual OFF
mode, the Timer operates but the programme settings are inactive.
3.
When the mode is turned from
Manual ON
to
Auto
, the Timer mode will remain ON until the next programmed timer off setting is reached.
4.
When the mode is turned from
Manual OFF
to
Auto
the timer mode will remain OFF until the next programmed timer ON setting is
reached.
Note - Timer Memory Back Up Batteries
Once the heater has been left plugged in with the socket switched on for at least 12 hours the timers memory back up batteries will be fully
charged.
Once the timer batteries are fully charged , if there is either a power cut or if the heater is disconnected from the mains for less than 100 hours,
then the timer will continue to keep time & the settings in the memory will remain intact .
If however the timer back up batteries have not been charged fully , or if the heater is deprived of power for longer than 100 hours , then the time
and the programme settings are likely to be lost and you may therefore need to reset the time and the programme before using in ‘Auto’ mode
again.
Setting Current Time
1.
Press the
S
(Set) button and keep pressed while pressing the
D
(Day) button until the actual day is displayed. Continue by pressing
H
(Hour) or
M
(Minute) button until the current hour or minute is displayed. When resetting, the buttons
D
,
H
or
M
can be held down for rapid
forward counting.
2.
Release both buttons. The day and time will now be set.
3.
To reset incorrect time, repeat previous steps.
Summertime Function
Summertime function is very useful for areas with summertime system , the timer can quickly & easily be changed to operate in SUMMER time
mode i.e. one hour ahead , and back again as follows ;
1.
Press the
S
(Set) and
MODE
(Input/Output) buttons simultaneously. The LCD will show ‘SUMMER’. The clock will switch ahead one hour.
2.
Press the buttons together again and the clock will switch back again one hour to standard time & ‘SUMMER’ will no longer be displayed
Setting Programs
Once the correct time is set , a total of 8 ON/OFF time programs can be set for AUTO operation. These can be set to operate on any of 16
different combinations of individual days or groups of days depending on your individual choice. To program the timer follow the setting
instructions;
1.
To select the first of your 8 ON/OFF programs simply press the
PROG
(Program) button once , the program is then input as follows ;
2.
You first select one of the 16 different combinations of individual days or groups of days you wish to set this program for. Continue to press
and release the
D
(Day) button to go through the choices until the day or blocks of days you require appears along the top of the timer
display then stop pressing , the 16 different combinations that can be chosen are as follow ;
1.)
Mo
7.)
Su
13.)
Tu, Th, Sa
2.)
Tu
8.)
Mo, Tu, We, Th, Fr, Sa, Su
14.)
Mo, Tu, We
3.)
We
9.)
Mo, Tu, We, Th, Fr
15.)
Th, Fr, Sa
4.)
Th
10.)
Sa, Su
16.)
Mo., We, Fr, Su
5.)
Fr
11.)
Mo, Tu, We, Th, Fr, Sa
6.)
Sa
12.)
Mo, We, Fr
