Operation
The heat output from this heater is regulated using the rotating wheels
shown in
Fig. 3
. By rotating these wheels, with the unit plugged in,
various fan and heat settings may be obtained.
Function control wheel
With the function control wheel, (f) in
Fig. 3
, the settings shown below
may be obtained;
0
Off
Fan only
1
Half Heat + Fan
2
Full Heat + Fan
Thermostat control wheel
The thermostat control wheel, (g) in
Fig. 3
, will adjust the temperature
cut off point of the heater.
Low Temperature
High Temperature
Both heat and fan operation can be regulated by the thermostat.
The thermostat, (g) in
Fig. 3
enables a constant local ambient temperature
to be maintained.
Turn the thermostat towards the back of the heater to the maximum
setting and allow the heater to operate until the room temperature has
reached the desired level.
Then turn back the thermostat until it ‘just’ operates. Cycling of the
thermostat will then occur to maintain this ambient temperature.
With the function switch in the
1
or
2
position, the heat is regulated by
the thermostat, whilst the fan continues to operate.
Installation
The CFP range of heaters are designed for free-standing use.
CAUTION
: DO NOT direct the air outlet grille, (c) in
Fig. 2,
towards the
ground or wall (min 1m) when in the free-standing position.
Safety in Use
This appliance incorporates a number of safety devices. In addition to
the safety precautions in the ‘Important Safety Advice’ section, your
attention is drawn to the following;
Tilt Switch
The tilt switch will prevent the heater from working if it is accidentally
tipped over or not standing upright. If this occurs, disconnect the power
and stand the heater back upright on a flat, stable surface and allow it to
cool. Reconnect the power and normal operation should be resumed.
If the heater does not operate, it is possible the thermal safety cut-out
has
activated
– refer to reset procedure in ‘Thermal Safety Cut-outs’
section.
Thermal Safety Cut-outs
The power supply to the heater may also be interrupted if one or a
combination of the following abnormal events occurs:
1.
Air inlet or outlet grilles are obstructed.
2.
Internal ventilation is impaired due to build up of dust and fluff.
3.
Fan failure.
To reset the cut-out follow the procedures below :
1.
Disconnect power supply.
2.
Determine what has caused the cut-out to operate and rectify.
( Note : This should only be undertaken by competent persons
with experience of repairing electrical appliances and in full
knowledge of the possible hazards involved ).
3.
After a short period of time, with the heater placed in a cool area,
the cut-out will reactivate allowing electrical supply to be
returned to the heater thus permitting normal operation.
Maintenance
Warning - Disconnect the heater from the mains supply before
carrying out maintenance.
This product is designed to require no maintenance. If operated in an
extremely dusty environment it may however be necessary to carefully
brush clean the rear air-inlet grille from time to time.
If the heater is to be placed in storage for long time intervals, Dampness
may penetrate the heating elements and with reactivation, EARTH FAULT
BREAKERS may trip. This is not a fault and can be rectified by feeding
the heater using a source without an earth fault breaker until the elements
have fully dried.
Recycling
For electrical products sold within the European
Community.
At the end of the electrical products useful life it should
not be disposed of with household waste. Please
recycle where facilities exist. Check with your Local
Authority or retailer for recycling advice in your country.
Cleaning
WARNING : ALWAYS DISCONNECT FROM THE POWER SUPPLY
BEFORE CLEANING THE HEATER
Do not use detergents, abrasive cleaning powders or polish of any kind
on the heater.
Wipe with a dry cloth to remove dust and a damp cloth (not wet) to clean
off stains. Be careful not to allow moisture into the heater.
Ensure that dust or fluff does not accumulate inside the heater as this
could lead to overheating of the element. Use a vacuum cleaner to remove
any fluff which does accumulate.
After Sales Service
Your product is guaranteed for one year from the date of purchase.
Within this period, we undertake to repair or exchange this product free
of charge (excluding element & subject to availability) provided it has
been installed and operated in accordance with these instructions.
Your rights under this guarantee are additional to your statutory rights,
which in turn are not affected by this guarantee.
Should you require after sales service you should contact our customer
services help desk on 0870 727 0101. It would assist us if you can
quote the model number, series, date of purchase, and nature of the fault
at the time of your call. The customer services help desk will also be able
to advise you should you need to purchase any spares.
Please do not return a faulty product to us in the first instance as this
may result in loss or damage and delay in providing you with a satisfactory
service.
Please retain your receipt as proof of purchase.
Glen Dimplex UK Limited
Millbrook House
Grange Drive
Hedge End
Southampton
Hampshire. SO30 2DF
UK customer help line (8.00AM – 6.00PM Mon-Fri; 8.30AM-1.00PM Sat)
Customer Services:
Tel.
0870 7270101
Fax.
0870 7270102
Republic of Ireland
Tel.
01 8424833
[c] Glen Dimplex UK Limited
All rights reserved. Material contained in this publication may not be reproduced in whole or in part, without prior permission in writing of Glen Dimplex UK Limited.
