11
the new board onto the mounts. Make sure the board
is secure.
8. Reassemble in the reverse order as above.
CAUTION:
When re-installing, be sure the wires are
guided and tucked into the proper openings along the right
side so they are not pinched and allows enough space to
reinstall the panel.
FLICKER MOTOR REPLACEMENT
WARNING:
Disconnect power before attempting any
maintenance or cleaning to reduce the risk of electric
shock or damage to persons.
CAUTION:
If unit was operating prior to servicing allow
at least 10 minutes for lights and heating elements to cool
off to avoid accidental burning of skin.
Tools required:
Phillips head screwdriver
Short handled Phillips head screwdriver
CAUTION:
Follow “Preparation for Service” instructions
before proceeding.
1. In the bottom right hand of the unit, remove both of the
access covers. (Figure 10)
2.
Remove the 2 screws holding the flicker motor to the
mounting bracket. Gently pull the motor away from the
flicker rod. (Figure 10)
3. Carefully remove the entire assembly.
4.
Remove the flicker motor wires from the terminal block
by loosening the 3 small Phillips screws holding each
wire in place then gently pulling the wires out of the
terminal block - noting their original locations.
5.
Properly orient the new flicker motor onto the bracket
and re-attach with the 2 mounting screws.
6. Reassemble in the reverse order as above.
CAUTION:
When removing and replacing the flicker
motor try to keep any slight bending of the flicker rod
minimal so as to not damage it. If flicker rod is damaged, it
should be replaced to ensure proper operation.
CAUTION:
When re-installing, be sure the wires are
guided and tucked into the proper openings along the right
side so they are not pinched and allows enough space to
reinstall the panels.
FLICKER ROD REPLACEMENT
WARNING:
Disconnect power before attempting any
maintenance or cleaning to reduce the risk of electric
shock or damage to persons.
CAUTION:
If unit was operating prior to servicing allow
at least 10 minutes for lights and heating elements to cool
off to avoid accidental burning of skin.
Tools required:
Phillips head screwdriver
Short handled Phillips head screwdriver
CAUTION:
Follow “Preparation for Service” instructions
before proceeding.
1. Remove the decorative acrylic ember-bed pieces from
the media tray, which lies along the bottom of the inte-
rior Partially Reflective Glass. A medium sized con
-
tainer such as a bucket or a box will be needed to keep
the acrylic ember-bed pieces together.
2.
Remove the Partially Reflective Glass retaining brack
-
ets by removing the 3 screws on each brackets, located
on the left and right side of the Partially Reflective
Glass. (Figure 12)
3.
Remove the Partially Reflective Glass. Carefully place
the glass assembly aside in a safe location.
4. In the bottom right hand of the unit, remove the two
screws and the front access cover. (Figure 10)
5. In the media tray, remove the two screws on either end
and the one on the side wall, to remove the clear media
tray and the front panel. (Figure 11)
!
NOTE:
Tip the front panel forward then lift out of the unit.
6.
Remove the flicker rod by holding the gasket and slid
-
ing it to the left. This will disengage it from the motor.
It will then be possible to remove it out of the opening.
7. Reassemble in the reverse order as above.
CAUTION:
When removing and replacing the flicker
motor try to keep any slight bending of the flicker rod
minimal so as to not damage it. If flicker rod is damaged, it
should be replaced to ensure proper operation.
CAUTION:
When re-installing, be sure the wires are
guided and tucked into the proper openings along the right
side so they are not pinched and allows enough space to
reinstall the panels.
LED LIGHT STRIPS
REPLACEMENT
WARNING:
Disconnect power before attempting any
maintenance or cleaning to reduce the risk of electric
shock or damage to persons.
CAUTION:
If unit was operating prior to servicing allow
at least 10 minutes for lights and heating elements to cool
off to avoid accidental burning of skin.
Tools required:
Phillips head screwdriver
Wire Snips
CAUTION:
Follow “Preparation for Service” instructions
before proceeding.
Figure 11
Media
Tray
Attachment
Screws
