manualshive.com logo in svg

Digitus RedRapid X, User Manual, Page: 45 / 124

Share
Download
Digitus RedRapid X User Manual Download Page 45

 

36

5.2.2. WAN 

 

Use the WAN Settings screen if you have already configured the Quick Setup Wizard section and 

you would like to change your Internet connection type. The WAN Settings screen allows to 

specify the type of WAN port connect you want to establish with your ISP. The WAN settings offer 

the following selections for the router’s WAN port, 

Channel

,

 ATM Setting

, 

ADSL Setting

, 

DNS

,

 

DDNS 

and

 RIP

. 

 

 

 

 

5.2.2.1. Channel Config 

 

ADSL modem/router supports 8 ATM Permanent Virtual Channels (PVCs) at the 

most. This page is used to configure the parameters for the channel operation 

modes of your ADSL Router. 

 

Before configuring the router, please check with your ISP (Internet Service 

Provider) what kind of the service is provided such as PPPoE, PPPoA or 

RFC1483/2684. Gather the information as illustrated in the following table and 

keep it for reference. 

 

Summary of Contents for RedRapid X





























































































































Reviews:

No comments