Digitus RedRapid X User Manual Download Page 109

Page: 109 / 124

100

Parameter

Description

Save Settings to File

Click Save button to save the ADSL router current

configuration to a file named "config.bin" on your PC.

Load Settings from File Click Browse button to search the file you have saved

before and click Upload button to restore the saved

configuration to the ADSL router.

Restore Settings to

Default

Click Reset button if you want to force the ADSL router to

perform a power reset and restore the original factory

settings.

5.4.2. Firmware

Upgrade

This page allows you to upgrade the firmware for the router. Click “Browse”

button to select the firmware file and click “Upload” button to start upgrading.

IMPORTANT!

Do not turn off your router while this procedure is in progress.

5.4.3. Ping

Once you have your router configured, you can send a ping command to the host

you specify in this page. To use it, you must know the IP address of the host you

Summary of Contents for RedRapid X





























































































































Search results

Summary of Contents for RedRapid X

Reviews:

Digitus RedRapid X, User Manual, Page: 109 / 124

Search results

Summary of Contents for RedRapid X

Reviews: