background image

1.

 

Introduction 

Digitus  DN-80223, with its 24 Gigabit RJ45 port and four 

independent SFP + fiber expansion slot, is ideal for connecting 

local networks to data centers. Equipped with 4x 10G SFP + slot, 

flexibly expand your network.  The 10G uplink switch provides 

high performance, enterprise QoS, advanced security policies 

and comprehensive layer 2  + management features. With all 

these advanced features, the switch is powerful and flexible 

enough to meet almost all IT needs. 

 

2.

 

Features 

1.

 

Support RJ45 Auto-MDI/MDIX 

2.

 

Panel light monitors working status and assists in fault 

analysis 

3.

 

Supports full-duplex IEEE 802.3x flow control and 

Backpressure half-duplex flow control 

4.

 

Support Energy-Efficient Ethernet (EEE) function 

(IEEE802.3az) 

5.

 

High reliability design, supporting traditional STP/RST layer 

2+ link protection technology; Supports manual 

aggregation and dynamic aggregation, which increases link 

bandwidth, improves link reliability, and implements load 

balancing and link backup 

6.

 

Management and maintenance Supports Console, Telnet, 

and SSH management modes 

7.

 

The system supports WEB management, which facilitates 

installation and debugging for engineers and maintenance 

personnel 

8.

 

Virtual Gateway Supports file upload and download 

management through TFTP 

 

Summary of Contents for DN-80223












Reviews: