Digitus DN-7039-B User Manual Download Page 65

Page: 65 / 76

DN-7039-B

108M Wireless Router User Guide

Current Statistics Status

default value is disabled. To

The IP Address displayed with statistics

Enable or Disable. The

enable, click the

Enable

button. If disabled, the function of DoS protection in

Security settings will be ineffective.

Packets Statistics Interval -

The default value is 10. Select a value between 5 and

60 seconds in the pull-down list. The Packets Statistic interval indicates the time
section of the packets statistic.

Sorted Rules -

Select sorted rule of statistics results as your desired.

Statistics Table:

Address

Packets

y the router.

The total amount of packets received and transmitted b

Total

The total amount of bytes received and transmitted by the router.

Bytes

Packets

The total amount of packets received and transmitted in the last

Packet

Statistic interval

seconds.

The total amount of bytes received and transmitted in the last

Packets

Bytes

Statistic interval

seconds.

The total amount of the ICMP packets transmitted to WAN in the last

ICMP Tx

Packets Statistic interval

seconds.

Current

The total amount of the UDP packets transmitted to WAN in the last

UDP Tx

Packets Statistic interval

seconds.

The total amount of the TCP SYN packets transmitted to WAN in the last

TCP

SYN Tx

Packets Statistic interval

seconds.

lick the

Save

tic interval

value.

button to save the

Packets Statis

Click the

Auto-refresh

checkbox to refresh automatically.

Refre

h immediately.

Click the

button to refres

Summary of Contents for DN-7039-B













































































Search results

Summary of Contents for DN-7039-B

Reviews:

Related manuals for DN-7039-B

Brands by name

Popular brands

Digitus DN-7039-B, User Manual

Search results

Summary of Contents for DN-7039-B

Reviews:

Related manuals for DN-7039-B

Brands by name

Popular brands