manualshive.com logo in svg

Digitus DN-16054, Installation Manual, Page: 6 / 20

Share
Download
Digitus DN-16054 Installation Manual Download Page 6

 

5 

3. ETHERNET CONNECTION 

Before using this network camera, please follow the instructions below to finish the 

network connection settings based on your installation environment: 

 

To configure the network settings, you must connect the camera to your PC by LAN. 

For details, please refer to “3.1 Network Connection via LAN” at page 5. 

 

To configure the network settings via Wizard, please refer to “3.2 Network 

Configurations via Wizard” at page 9. 

 

To configure the network settings via our supplied CMS software, Video Viewer, 

please refer to “3.3 Network Configurations via Video Viewer” at page 13. 

3.1 Network Connection via LAN 

Step1: Connect this network camera and your PC via a RJ45 network cable, and make 

sure the camera is powered on. 

Step2: Set the PC’s IP address as “192.168.1.XXX” (1~255, except 10). 

For Windows 2000 users: 

a) Select 

“Start” 

 “Settings” 

 “Network and Dial-up Connections”.   

b)  Right-click on “Local Area Connection”, and select “Properties”. 

 

c)  In the “General” tab, select “Internet Protocol (TCP/IP)”, and select “Properties”. 

 

Summary of Contents for DN-16054





















Reviews:

No comments