background image

WARRANTY

:  

We at 

DigiTech®

 are very proud of our products and back-up each one we sell with the following warranty:

1.  Please register online at www.digitech.com within ten days of purchase to validate this warranty. This warranty is 

valid only in the United States.

2.  DigiTech warrants this product, when purchased new from an authorized U.S. DigiTech dealer and used solely within 

the U.S., to be free from defects in materials and workmanship under normal use and service. This warranty is valid 

to the original purchaser only and is non-transferable.

3.  DigiTech liability under this warranty is limited to repairing or replacing defective materials that show evidence of 

defect, provided the product is returned to DigiTech WITH RETURN AUTHORIZATION, where all parts and labor 

will be covered up to a period of one year (this warranty is extended to a period of six years when the product 

has been properly registered through our website). A Return Authorization number may be obtained from DigiTech 

by telephone. The company shall not be liable for any consequential damage as a result of the product’s use in any 

circuit or assembly.

4.  Proof-of-purchase is considered to be the responsibility of the consumer. A copy of the original purchase receipt 

must be provided for any warranty service.

5.  DigiTech reserves the right to make changes in design, or make additions to, or improvements upon this product 

without incurring any obligation to install the same on products previously manufactured.

6.  The consumer forfeits the benefits of this warranty if the product’s main assembly is opened and tampered with by 

anyone other than a certified DigiTech technician or, if the product is used with AC voltages outside of the range 

suggested by the manufacturer.

7.  The foregoing is in lieu of all other warranties, expressed or implied, and DigiTech neither assumes nor authorizes 

any person to assume any obligation or liability in connection with the sale of this product. In no event shall DigiTech 

or its dealers be liable for special or consequential damages or from any delay in the performance of this warranty 

due to causes beyond their control.

NOTE:

 The information contained in this manual is subject to change at any time without notification. Some information 

contained in this manual may also be inaccurate due to undocumented changes in the product or operating system since 

this version of the manual was completed. The information contained in this version of the owner’s manual supersedes all 

previous versions.

Summary of Contents for HARDWIRE CR-7

























Reviews: