Digital Watchdog MEGApix DWC-MVT4Wi28 Page 28 User Manual Download | Manualshive

Page: 28 / 63

background image

6

.4.4 Alarm Out

This function is only available for some models. Go to Config

→

Alarm

→

Alarm Out.

Alarm Out Mode: Alarm linkage, manual operation, day/night switch linkage and
schedule are optional.
Alarm Linkage: Having selected this mode, select alarm out name and alarm holding
time at the “Alarm Holding Time” pull down list box.
Manual Operation: Having selected this mode, click “Open” to trigger the alarm out
immediately; click “Close” to stop alarm.

Day/Night Switch Linkage: Having selected this mode, choose to open or close
day/night switch linkage.

Schedule: Click “Add” and drag the mouse on the timeline to set the schedule of
alarm out; click “Erase” and drag the mouse on the timeline to erase the set time
schedule. After this schedule is saved, the alarm out will be triggered in the specified
time.

6

.4.5 Alarm Server

Go to Alarm

→

Alarm Server interface as shown below.

Set the server address, port, heartbeat and heartbeat interval. When an alarm occurs,
the camera will transfer the alarm event to the alarm server. If an alarm server is not
needed, there is no need to configure this section.

2

8

«
...
26
27
28
29
30
...
»

Summary of Contents for MEGApix DWC-MVT4Wi28
































































Reviews:

No comments

Related manuals for MEGApix DWC-MVT4Wi28

Brand: Panasonic Pages: 15

AWHE100N - HD INTEGRATED CAMERA

Brand: Panasonic Pages: 42

Brand: Panasonic Pages: 2

Brand: 3xLogic Pages: 25

VX-2A-B-IWD (R)

Brand: 3xLogic Pages: 80

DeltaSphere-3000

Brand: 3rdTech Pages: 9

Brand: Campbell Pages: 116

Brand: Dahua Pages: 20

Brand: Viewpro Pages: 10

Brand: Olympus Pages: 116

Visiondrive 84 04 63

Brand: Conrad Pages: 8

SurveyorVFTXX134-60-01

Brand: Vicon Pages: 23

Brand: TecnoVideo Pages: 4

Brand: XNET Pages: 23

Brand: Zavio Pages: 13

Brand: Super Circuits Pages: 28

Brand: SOMFY Pages: 40

Brand: Grundig Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands