background image

12

13

3-1. Control panel

You can control the basic paper feeding operations of the printer with the button on the control panel. 
The indicator lights help you to monitor the printer’s status.

Control Panel

 

 

 

Button

The button can be disabled by the ESC c 5 command.

Press the FEED button once to advance paper one line. You can also hold down the FEED button to 
feed paper continuously.

3-2. Error indicators

This section explains the different patterns signaled by the three LED indicators located on the top 
cover of the printer.

STATUS

PAPER

ERROR

POWER

REMARKS

RED

RED

GREEN

Power off

OFF

OFF

OFF

Normal power is not supplied to 

the printer

Power on

OFF

OFF

ON

Normal power is supplied to the 

printer

On line

OFF

OFF

ON

Normal error-free mode

Cover open

OFF

ON

ON

Close cover

Paper empty

OFF

ON

ON

Insert new paper roll

Paper near end

ON

OFF

ON

Paper is low

Test mode

OFF

OFF

ON

Ignored error led

3. Control panel and other functions

2-4. Adjustment of paper width

1. Please adjust the Paper Guide to fit to the paper width as the direction of arrow.

2. Tight the screw after adjusting the Paper Guide.

3. Pull the edge of paper once the paper roll is installed correctly and close the Paper Cover.

Summary of Contents for DS-820














Reviews: