manualshive.com logo in svg

Digi 70002405, User Manual

Share
Download
Digi 70002405 User Manual Download Page 124

Configure the device using the ConnectPort LTS web interface

Administration

Digi ConnectPort LTS User Guide

124

Update the BIOS code

You can only update the BIOS code through the boot loader. To update BIOS code, see

ConnectPort

LTS disaster recovery

.

Important

Before uploading the firmware, read the firmware Release Notes to see if you need to

update the BIOS code before updating the firmware.

Factory default settings

Restoring a ConnectPort LTS device to its factory default settings clears all current configuration
settings with some exceptions. See the following topics for more information:

n

Settings cleared and retained during a factory reset

n

File Management

There are several ways to reset the device configuration of a ConnectPort LTS product to the factory
default settings:

n

From the

web interface

using the Restore Factory Defaults operation

This method is the best way to reset the configuration, because you can back up the settings

using the Backup/Restore operation. The Backup/Restore operation provides a means to

restore the configuration after the configuration issues have been resolved. See

Reset the

factory settings on a ConnectPort LTS product from the web interface

for more information.

n

From the command-line interface, using the

boot

or

revert

commands

n

Using the reset button on the ConnectPort LTS device

Use this method if you cannot access the device from a web browser. The location of the reset

button may vary. See

Reset the factory settings on a ConnectPort LTS product using the Reset

button

for more information.

n

From the LCD display under

Miscellaneous

Settings cleared and retained during a factory reset

A factory reset does not delete files uploaded to the File Management page. See

Factory reset does

not delete custom files

for more information.

n

Restore

: Returns the configured settings on the Digi device to the factory defaults.

n

Keep network settings

: Select this check box to retain the IP address settings.

n

Restore Only Serial Port Settings

: Select this check box to restore only the serial settings to

their factory defaults. The other configuration settings remain as-is.

Reset the factory settings on a ConnectPort LTS product from the web interface

To reset the factory settings on the ConnectPort LTS device from the web interface:

1. Create a backup copy of the configuration using the Backup/Restore operation. See

Backup/Restore

for more information.

2. Select

Administration

>

Factory Default Settings

. The Factory Default Settings page appears.

Summary of Contents for 70002405




































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands