Diamond Products CC6571, Operator'S Manual, Page: 41 / 64

CC65
Rear
Lubr
ever
PTO
Add
Use
base
Inne
Insta
1. C
o
2. R
f
3. P
o
4. A
s
5. P
s
s
Rem
1. R
f
2. R
3. C
o
4. P
s
Rea
Insp
wear
571 - CC6571-3
r Axle
ricate both p
ry 40 hours o
three pump
high temper
ed grease.
er Blade Fl
F
alling the Inn
Check the in
or replace as
Remove the
flange using
Place the inn
of the blade
Apply Loctite
setscrew thre
Place the se
setscrew hol
shaft key to s
moving the Inn
Remove the
flange using
Remove the
Check the in
or replace as
Place the se
setscrew hol
ar Wheels
ect the rear
r and replac
3 Concrete Saw
pillow block b
of operation.
s of grease
rature, extre
lange
Figure 70: Inn
ner Blade Fla
nner flange fo
s necessary
setscrew fro
an Allen wre
ner flange on
shaft.
e 262 (red) o
eads.
tscrew into t
le and tighte
secure the in
ner Blade Fla
setscrew fro
an Allen wre
inner flange
nner flange fo
s necessary
tscrew into t
le and tighte
wheels regu
e as necess
w Manual
bearing grea
.
to PTO ever
eme pressure
er Flange
ange
or damages
.
om the back
ench.
nto the inden
or an equiva
the inner flan
en it down to
nner flange.
ange
om the back
ench.
e from the bl
or damages
the inner flan
en to secure.
ularly for dam
sary.
ase fittings
ry 25 hours.
e, Lithium
and clean
k of the inner
nted portion
lent to the
nge
the blade
k of the inner
ade shaft.
and clean
nge
.
mages or
r
r
1
2
3
4
Bat
Ign
em
exp
ope
bat
Dis
ma
Use
vol
Use
avo
bat
Batt
12 V
1. Unscrew
remove o
Fi
2. Place th
3. Place th
hole and
(237 Nm
the bush
the saw
.
4. Repeat s
wheel.
ttery
WARNIN
nitable explo
mitted from th
pose the bat
en flames, a
ttery well-ve
sconnect the
aintenance.
CAUTIO
e a proper b
tmeter, to te
e protective
oid contact w
ttery.
tery Type
Volt, Group 2
w the trantorq
one of the re
igure 71: Tran
e new whee
e trantorque
d tighten the
m).
Note: Fail
hing may cau
.
steps 1–3 to
NG
osive gases a
he battery. D
ttery to spar
and keep the
ntilated.
e battery whe
ON
battery teste
est the batte
eyewear or
with the skin
24
que bushing
ear wheels.
ntorque Bushi
el onto the re
e bushing int
bushing to
ilure to prope
use the whe
o replace the
are
DO NOT
ks or
e area aroun
en performin
r, such as a
ry strength.
r a face shiel
n when hand
g and
ng
ear axle.
to the wheel
175 ft-lb
erly tighten
eel to fall off
e second
nd the
ng
ld, and
ling a
41