manualshive.com logo in svg

DH RGI-30, Short Manual, Page: 10 / 26

Share
Download
DH RGI-30 Short Manual Download Page 10

 

8 

 

 

Basic control registers

: initialization, force setting, reference position, speed, and some 

states. 

 

 

Configuration registers

: gripper’s parameter configuration. Includes Modbus 

communication parameters and I/O parameters.

 

 

Table 2.2 Basic Control register map

 

Function 

high- 

byte 

low- 

byte 

Description 

Write 

Read 

Initialization 

0x01 

0x00 

Initialize the 

gripper

 

0x01

：

initialization

；

0xA5: Fully 

initialization

 

Current setting

 

Force 

0x01 

Gripper’s 

force

 

20-100 (%) 

Force

 

currently set

 

Reserved 

0x02 

-

 

- 

-

 

Position 

0x03 

Position

 

0-1000 (

‰

) 

Reference position currently 

set

 

Speed 

0x04 

Speed

 

1-100 (%) 

Speed

 

currently set

 

Rotation 

angle 

0x05 

Rotate to the 

specified 

angle.

 

-32768-32767,angle 

value. 

Read the current setting

 

Reserved 

0x06 

-

 

- 

-

 

Rotation 

speed 

0x07 

Rotate at a set 

speed.

 

1-100% 

Read the current setting.

 

Rotation 

force 

0x08 

Rotate at a set 

force.

 

20-100% 

Read the current setting.

 

Initialization 

state   

0x02 

0x00 

Initialization 

state of the 

gripper

 

Read Only 

0

：

Uninitialized

；

 

1

：

Initialized 

2

：

Initializing 

Gripper state   

0x01 

Gripper state

 

Read Only 

0

：

In motion; 

1

：

Reach position

；

 

2:object caught

；

 

3

：

Object dropped 

Position   

0x02 

gripper 

position 

 

Read Only 

Current actual position

 

Rotating 

angle 

feedback. 

0x08.

 

Feedback on 

the current 

rotation angle.

 

Cannot be written.

 

Read the current value.

 

Rotating 

initialization 

state 

feedback. 

0x0A. 

Feedback 

rotation 

initialization 

state. 

Cannot be written. 

0:Uninitialized; 

1:Initialized successfully. 

2

：

Initializing 

Rotating 

state 

feedback. 

0x0B.

 

Feedback 

rotation state.

 

Cannot be written.

 

0: In motion,

 

1 : reaching the angle;

 

2: blocking;

 

3: blocked during reaching 

the specified position.

 

 

 

 

Summary of Contents for RGI-30



























Reviews:

No comments