background image

GB-K Gas Booster Package Operation and Maintenance Manual 

 

 

 

© 1998 - 2000 

DH Instruments, Inc

 

 

 

 

 This equipment described in this manual is designed and manufactured for the intended purpose of 

generating high pressure gas and regulating two independent gas output pressures.  Certain precautions 
need to be followed during installation and operation of this device.  Reading and understanding the 
material is essential to the safe and correct operation of the unit. 

 

 

 Pressurized equipment is potentially dangerous.  The equipment described in this manual generates and 

controls very high gas pressures.  It should not be operated by anyone who has not thoroughly familiarized 
themselves with this manual.  Additional training in general and pressure specific safety procedures will 
help assure protection from harm or damage to personnel or property.  Responsibility for the proper and 
safe operation of this instrument rests with the user. 

 

 

 Do not use oxygen.  This instrument is not compatible with the use of oxygen.  Hydrocarbon elastomers 

and lubricants are present. 

 

 

 High pressure liquids and gases are potentially hazardous.  Energy stored in these liquids and gases can 

be released unexpectedly and with extreme force.  High pressure systems should be assembled and 
operated only by personnel who have been instructed in proper safety practices. 

 

 
 
 
 
 
 
 
 
 

©

 1998 ~ 2000, 

DH Instruments, Inc.

  All rights reserved. 

Information in this document is subject to change without notice.  No part of this document may be reproduced or 
transmitted in any form or by any means, electronic or mechanical, for any purpose, without the express written 
permission of 

DH Instruments, Inc.  

4765 East Beautiful Lane  Phoenix  AZ  85044-5318  USA. 

DH Instruments 

makes every effort to ensure the accuracy and quality of it’s published materials; however, 

no warranty, expressed or implied, is provided.  

DH Instruments 

disclaims any responsibility or liability for any direct 

or indirect damages resulting from the use of the information in this manual or products described in it.  Mention of 
any product or brand does not constitute an endorsement by 

DH Instruments 

of that product or brand.  This manual 

was originally composed in English and was subsequently translated into other languages.  The fidelity of subsequent 
translations cannot be guaranteed.  In case of conflict between the English version and another language version, 
the English version predominates. 

DH Instruments

DH

 , 

DHI

, PPC, PPCK+, PPC2+, RPM3 and CalTool are trademarks, registered and otherwise. 

Swagelok

 is a registered trademark of the Swagelok Company. 

Teflon

 is a registered trademark of the 3M Corporation. 

 

 

Document No. 550082a 
000822 
Printed in the USA. 

Summary of Contents for GB-K-152





































Reviews: