DFI SR330-N User Manual Download Page 81

Page: 81 / 155

BIOS Setup

USB 1.0 Controller

This field is used to enable or disable the Universal Host Controller
Interface (USB 1.0).

USB 2.0 Controller

This field is used to enable or disable the Enhanced Host Controller
Interface (USB 2.0).

USB Storage Function

This field is used to enable or disable the support for legacy USB
mass storage.

The settings on the screen are for reference only. Your version may not be
identical to this one.

Phoenix - AwardBIOS CMOS Setup Utility

USB Device Setting

Item Help

Menu Level

↑↓→←

: Move

Enter: Select

F1: General Help

+/-/PU/PD: Value

F10: Save

ESC: Exit

F5: Previous Values

F6: Fail-Safe Defaults

F7: Optimized Defaults

USB 1.0 Controller
USB 2.0 Controller
USB Storage Function

*****USB Mass Storage Device Boot Setting****

Enabled
Enabled
Enabled

USB Device Setting

Move the cursor to this field and press <Enter>. The following
screen will appear.

Summary of Contents for SR330-N




























































































































































Search results

Summary of Contents for SR330-N

Reviews:

Related manuals for SR330-N

Brands by name

Popular brands

DFI SR330-N, User Manual

Search results

Summary of Contents for SR330-N

Reviews:

Related manuals for SR330-N

Brands by name

Popular brands