DFI LT600-DR/D/L User Manual Download Page 127 | Manualshive

Page: 127 / 148

background image

127

5

RAID

4. Read the warning carefully

then click Next.

Step 5: Install the Intel Matrix Storage Manager for RAID/AHCI

The Intel Matrix Storage Manager can be installed from within Windows. It allows
RAID  volume  management  (create,  delete,  migrate)  from  within  the  operating
system. It will also display useful SATA device and RAID volume information. The
user  interface,  tray  icon  service  and  monitor  service  allow  you  to  monitor  the
current  status  of  the  RAID  volume  and/or  SATA  drives.  It  enables  enhanced  per

-

formance and power management for the storage subsystem.

1. Insert the provided CD into an optical drive.

2. Click “Intel Matrix Storage Manager for RAID/AHCI” on the main menu.

3. Setup is ready to install

the utility. Click Next.

«
...
125
126
127
128
129
...
»

Summary of Contents for LT600-DR/D/L





















































































































































Reviews:

No comments

Related manuals for LT600-DR/D/L

Brand: Acer Pages: 15

Brand: Acer Pages: 12

Brand: Xilinx Pages: 14

Brand: MSI Pages: 19

Brand: MotorGuide Pages: 21

PIC18F57Q84 Curiosity Nano

Brand: Microchip Technology Pages: 39

Brand: Texas Instruments Pages: 19

Brand: Sanela Pages: 30

970A-G46 Series

Brand: MSI Pages: 78

Brand: DFI Pages: 115

Brand: Javad Pages: 12

Brand: Foxconn Pages: 75

Brand: ASROCK Pages: 20

Brand: Zamel Pages: 3

Brand: Linear Technology Pages: 8

Brand: MSI Pages: 92

Brand: Gigabyte Pages: 23

Brand: IEI Technology Pages: 165

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands