29
EnGLIsH
Vac Rack Installation (Fig. M)
1. Remove the 4 carry handle screws using a T-25 star bit and
remove the carry handle.
2. Install the vac rack reusing the carry handle screws. Put
them back in their original holes and tighten.
3. Use the 2 screws
32
provided by placing them in the rear
holes of the vac rack. Push down and turn each screw to
Accessories
WARNING:
Since accessories, other than those offered
by
D
e
WALT
, have not been tested with this product, use of
such accessories with this appliance could be hazardous.
To reduce the risk of injury, only
D
e
WALT
recommended
accessories should be used with this product.
ACCESSORIES
DWV9340-XJ
Dust Class M Filter
DWV9345-XJ
Dust Class H Filter
DWV9315-XJ
Crush-proof hose
DWV9316-XJ
Anti-static hose;
diameter 32mm
DWV9401-XJ
Paper bag
DWV9400-XJ
Plastic liner
DWV9402-XJ
Fleece bag
DWV9500-XJ
Vac Rack
DWV9345-XJ
ToughSystem®, TSTAK®
Vac Rack
D
e
WALT
AirLock System
DWV9000
Twist-Lock connection
DWV9110
29–35 mm tapered
rubber adapter
DWV9120
35–38 mm stepped
rubber adapter
DWV9130
35 mm OD adapter
DWV9150
35 mm OD angle
adapter
Storage (Fig. I)
1. Empty the canister, refer to
To Empty canister
under
Operation
.
2. Clean the vacuum inside and outside.
3. Clean or replace filters, refer to
Filters
.
4. Remove the hose
7
from the twist-lock hose inlet
10
and
close the inlet with the inlet plug
19
5. Put the ends of the suction hose together to prevent dirt
particles from escaping.
6. Store the suction hose and the power cord as shown in the
illustration. Place the unit in a dry room and secure it from
unauthorized use.
nOTE:
Plug inlet plug into inlet to keep debris inside
canister when suction hose is removed. You can also attach
the ends of the hose together and lock together with the
twist-lock end.
nOTE:
After wet applications, the internal parts of the liquid
container must be dried before storage.
Cleaning
WARNING:
Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the appliance. These
chemicals may weaken the materials used in these parts.
Never let any liquid get inside the machine; never immerse
any part of the appliance into a liquid.
1. Vacuum the outside of the dust extractor. For further
cleaning use a cloth dampened only with water and mild
soap if necessary.
2. After use dispose of cloth in an appropriate container.
Lubrication
Your dust extractor requires no additional lubrication.
3. For DWV905H, loosen the 2.5 mm socket head screw
28
using
a T-10 bit, then remove the filter plate
29
from the filters as
shown in Fig. J. Do not reuse the Class H main filter element
after it has been removed from the unit.
4. Turn each filter
9
counterclockwise by gripping it on the
plastic end cover as shown in Fig. K, and carefully remove
from head, ensuring debris does not fall into mounting hole.
nOTE
: Use care to not damage filter material.
5. If the bottom side of the vacuum head needs to be cleaned,
use a cloth dampened with water and mild soap and allow
it to dry. Dispose of cloth in an appropriate container.
6. Inspect filters for wear, tears or other damage.
WaRnInG:
If there is any doubt on the condition of the
filters, they MUST be replaced. DO NOT continue use if
filters are damaged. Class H filters should not get cleaned
manually outside of the unit.
WARNING:
Never use compressed air or a brush to clean
filters, otherwise damage to the filter membrane will occur
which will allow dust to pass through the filter. If needed,
gently tap against a hard surface or rinse with room
temperature water and let air dry. Cleaning of the filters
is typically unnecessary, even if the filter is covered with
dust. The automatic filter cleaning system will maintain
maximum performance and continue to function. If visual
damage to the filter membrane exists, replace filters. Filters
typically last between six and twelve months depending
on use and care.
To Install Filters (Fig. J, L)
1. Ensure filter seal
30
is in place and is secure
2. Line up filter threads
31
to vacuum head threads and using
moderate force, turn filter clockwise until tight.
nOTE:
Use care to not damage filter material.
3. For DWV905H, replace the filter plate
29
and tighten the
filter screw
28
on top of the plate.
4. secure by replacing the filter rod
28
as shown in Fig. J.
5. Place the vacuum head
3
onto the container and secure it
by closing the canister latches
4
.
Summary of Contents for DWV905H
