background image

English

12

Cleaning

 

WARNING:

 Blow dirt and dust out of all air vents with 

clean, dry air at least once a week. To minimize the risk 
of eye injury, always wear ANSI Z87.1 approved eye 
protection when performing this.

 

WARNING:

 Never use solvents or other harsh 

chemicals for cleaning the non-metallic parts of 
the tool. These chemicals may weaken the plastic 
materials used in these parts. Use a cloth dampened 
only with water and mild soap. Never let any liquid 
get inside the tool; never immerse any part of the tool 
into a liquid.

Accessories

 

WARNING: 

Since accessories, other than those 

offered by 

D

e

WALT

, have not been tested with this 

product, use of such accessories with this tool could be 
hazardous. To reduce the risk of injury, only 

D

e

WALT

 

recommended accessories should be used with 
this product.

Recommended accessories for use with your tool 
are available at extra cost from your local dealer or 
authorized service center. If you need assistance in 
locating any accessory, please contact 

D

e

WALT

 Industrial 

Tool Co., 701 East Joppa Road, Towson, MD 21286, call 
1-800-4-

D

e

WALT

 (1-800-433-9258) or visit our website: 

www.dewalt.com.

Repairs

 

WARNING: 

To assure product SAFETY and 

RELIABILITY, repairs, maintenance and adjustment 
(including brush inspection and replacement) should 
be performed by a 

D

e

WALT

 factory service center 

or a 

D

e

WALT

 authorized service center. Always use 

identical replacement parts.

Register Online

Thank you for your purchase. Register your product now for:
• 

WARRAnTY sERViCE:

 Registering your product will 

help you obtain more efficient warranty service in case 
there is a problem with your product.

• 

COnFiRMATiOn OF OWnERshiP:

 In case of 

an insurance loss, such as fire, flood or theft, your 
registration of ownership will serve as your proof 
of purchase.

• 

FOR YOUR sAFETY: 

Registering your product will 

allow us to contact you in the unlikely event a safety 
notification is required under the Federal Consumer 
Safety Act.

Register online at www.dewalt.com/register.

Three Year Limited Warranty

D

e

WALT

 will repair, without charge, any defects due to 

faulty materials or workmanship for three years from 
the date of purchase. This warranty does not cover part 
failure due to normal wear or tool abuse. For further detail 
of warranty coverage and warranty repair information, 
visit www.dewalt.com or call 1-800-4-

D

e

WALT

 (1-800-

433-9258). This warranty does not apply to accessories 

or damage caused where repairs have been made 
or attempted by others. THIS LIMITED WARRANTY IS 
GIVEN IN LIEU OF ALL OTHERS, INCLUDING THE IMPLIED 
WARRANTY OF MERCHANTABILITY AND FITNESS FOR A 
PARTICULAR PURPOSE, AND EXCLUDES ALL INCIDENTAL 
OR CONSEQUENTIAL DAMAGES. Some states do not allow 
limitations on how long an implied warranty lasts or the 
exclusion or limitation of incidental or consequential 
damages, so these limitations may not apply to you. This 
warranty gives you specific legal rights and you may have 
other rights which vary in certain states or provinces.
In addition to the warranty, 

D

e

WALT

 tools are covered 

by our:

1 YEAR FREE sERViCE

D

e

WALT

 will maintain the tool and replace worn parts 

caused by normal use, for free, any time during the first year 
after purchase.

90 DAY MOnEY BACK gUARAnTEE

If you are not completely satisfied with the performance of 
your 

D

e

WALT

 Power Tool, Laser, or Nailer for any reason, you 

can return it within 90 days from the date of purchase with 
a receipt for a full refund – no questions asked.

lATin AMERiCA: 

This warranty does not apply to products 

sold in Latin America. For products sold in Latin America, 
see country specific warranty information contained in 
the packaging, call the local company or see website for 
warranty information.

FREE WARning lABEl REPlACEMEnT:

 If your warning 

labels become illegible or are missing, call 1-800-4-

D

e

WALT

 

(1-800-433-9258) for a free replacement.

Summary of Contents for DWE43265N

















































Reviews: