OPENING
OUVERTURE
ABERTURA
TAB
LANGUETTE
LENGÜETA
FIG. 2
FIG. 3
1
2
FIG. 1
FIG. 4
WARNING
AVERTISSEMENT
ADVERTENCIA
TO REDUCE THE RISK OF INJURY, READ AND
UNDERSTAND THE TOOL STAND INSTRUCTION SHEET
AND THE TOOL INSTRUCTION MANUAL BEFORE USE. FOR USE WITH DW744 TABLE
SAW ONLY. ENGAGE TOOL IN STAND AND OPEN FULLY BEFORE USE. MAXIMUM LOAD
EQUALS 150 LBS. (68KG). DO NOT CLIMB, SIT OR STAND ON SAW STAND. DO NOT USE
ON SLOPED, UNEVEN OR UNSTABLE SURFACES. USE ONLY FROM THIS SIDE.
PARA REDUCIR EL RIESGO DE LESIÓN, LEA Y ENTIENDA LA HOJA DE
INSTRUCCIÓN DEL SOPORTE DE LA HERRAMIENTA Y EL MANUAL DE
INSTRUCCIÓN DE LA HERRAMIENTA ANTES DE USO. PARA EL USO CON LA SIERRA DE LA TABLA DW744
SOLAMENTE. COLOQUE LA HERRAMIENTA EN LA BASE Y ÁBRASE COMPLETAMENTE ANTES DE USO. LA CARGA
MÁXIMA IGUALA 150 LIBRAS. (68KG). NO SUBA, NO SE SIENTE NI ESTÉ PARADO EN SOPORTE DE LA SIERRA. NO
UTILICE EN SUPERFICIES INCLINADAS, DESIGUALES O INESTABLES. UTILICE SOLAMENTE DE ESTE LADO.
POUR RÉDUIRE LE RISQUE DE DOMMAGES, LISEZ ET COMPRENEZ LA FEUILLE
D'INSTRUCTION DE STAND D'OUTIL ET LE MANUEL D'INSTRUCTION D'OUTIL AVANT
L'EMPLOI. POUR L'USAGE AVEC LA SCIE DU TABLEAU DW744 SEULEMENT. ENGAGER L’OUTIL DANS LE SOCLE ET OUVREZ-VOUS
ENTIÈREMENT AVANT L'EMPLOI. LA CHARGE MAXIMUM ÉGALE 150 LIVRES. (68KG). NE VOUS ÉLEVEZ PAS, NE VOUS REPOSEZ PAS OU
NE VOUS TENEZ PAS SUR LE STAND DE SCIE. N'EMPLOYEZ PAS SUR LES SURFACES INCLINÉES, INÉGALES OU INSTABLES. EMPLOYEZ
SEULEMENT DE CE CÔTÉ.
MADE IN CHINA/HECHO EN CHINA/FABRIQUÉ EN CHINE
FIG. 5
Heavy Duty Table Saw Stand DW7440
WARNING:
For your own safety, read the
table saw instruction
manual before using any accessory. Failure to heed these
warnings may result in personal injury and serious damage to the
table saw and the accessory. When servicing this tool, use only
identical replacement parts.
• This table saw stand is designed only for use with the DW744
and DW744X table saws. Do not use this stand with any other
tool.
• Do NOT mount the table saw to the stand in any other
orientation.
• Feet should be assembled to the end of the legs as shown.
• Position all of the feet in the same orientation or unstable footing
may occur.
• Open saw stand fully before use.
• Maximum load: 150 lbs. (68kg.)
• Do not climb on or sit on saw stand.
• Do not use saw stand on inclined, uneven or unstable
surfaces.
• The back legs of the saw stand are slightly longer than the
front legs to provide additional support. Use the saw stand and
operate the table saw from the front side only.
• Do not use saw stand if it is damaged or bent.
SAVE THESE INSTRUCTIONS
ASSEMBLY
• Assemble as shown in Figure 1.
TO OPEN TABLE SAW STAND
1. Unfold the saw stand until it is fully opened. Place it upright, as
shown in Figure 2.
2. Place the table saw on the saw stand. Place the tabs on the
front of the table saw into the openings on the front of the saw
stand, as shown in Figure 3. Ensure the tabs fit snugly into the
openings. Be sure that the rear of the base is resting on the
lower step of the frame (Fig. 4) and does not rock or wobble in
place. DO NOT mount the table saw to the saw stand in any
other orientation.
TO CLOSE TABLE SAW STAND
1. Lift the table saw from the saw stand.
2. Pick the stand up by the top rails and close it.
CAUTION:
Be sure the saw is mounted firmly to your stand before
using it.
FREE WARNING LABEL REPLACEMENT:
If your warning labels
(Fig. 5) become illegible or are missing, call 1-800-4-D
E
WALT for a
free replacement.
D
E
WALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286 (NOV06) Form No. 153513-04
DW7440 Copyright © 1997, 1999, 2006 D
E
WALT
The following are trademarks for one or more DeWALT power tools: the yellow and black color scheme; the “D” shaped air intake grill; the array of pyramids
on the handgrip; the kit box configuration; and the array of lozenge-shaped humps on the surface of the tool.
