background image

1

English

1) WORK AREA SAFETY

a) 

Keep work area clean and well lit. 

Cluttered or dark areas 

invite accidents.

b)

 Do not operate power tools in explosive atmospheres, 

such as in the presence of flammable liquids, gases or 
dust. 

Power tools create sparks which may ignite the dust or 

fumes.

c)

 Keep children and bystanders away while operating a 

power tool. 

Distractions can cause you to lose control.

2) ELECTRICAL SAFETY

a)

 Power tool plugs must match the outlet. Never modify 

the plug in any way. Do not use any adapter plugs with 
earthed (grounded) power tools. 

Unmodified plugs and 

matching outlets will reduce risk of electric shock.

b)

 Avoid body contact with earthed or grounded surfaces 

such as pipes, radiators, ranges and refrigerators. 

There 

is an increased risk of electric shock if your body is earthed or 
grounded.

c)

 Do not expose power tools to rain or wet conditions. 

Water entering a power tool will increase the risk of electric 
shock.

d)

  Do not abuse the cord. Never use the cord for carrying, 

pulling or unplugging the power tool. Keep cord away 
from heat, oil, sharp edges or moving parts. 

Damaged or 

entangled cords increase the risk of electric shock. 

e)

  When operating a power tool outdoors, use an extension 

cord suitable for outdoor use. 

Use of a cord suitable for 

outdoor use reduces the risk of electric shock. 

f)

  If operating a power tool in a damp location is unavoidable, 

use a ground fault circuit interrupter (GFCI) protected 
supply. 

Use of a GFCI reduces the risk of electric shock.

Defi nitions: Safety Guidelines 

The definitions below describe the level of severity for each 
signal word. Please read the manual and pay attention to these 
symbols.

DANGER:

 Indicates an imminently hazardous situation 

which, if not avoided, 

will 

result in 

death or serious injury

.

WARNING:

 Indicates a potentially hazardous situation 

which, if not avoided, 

could

 result in 

death or serious injury

.

CAUTION:

 Indicates a potentially hazardous situation which, 

if not avoided, 

may

 result in 

minor or moderate injury

.

NOTICE: 

Indicates a practice

 not related to personal injury 

which, if not avoided,

 may 

result in

 property damage

.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR 
ANY D

E

WALT TOOL, CALL US TOLL FREE AT: 

1-800-4-D

E

WALT 

(1-800-433-9258)

.

  WARNING:

 To reduce the risk of injury, read the instruction 

manual.

General Power Tool Safety Warnings

 

WARNING! Read all safety warnings and all instructions. 

Failure to follow the warnings and instructions may result in 
electric shock, fire and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS 

FOR FUTURE REFERENCE

The term “power tool” in the warnings refers to your mains-operated 
(corded) power tool or battery-operated (cordless) power tool.

Summary of Contents for DCS391B




















Reviews: