DeWalt D25892, Original Instructions Manual

Page: 8 / 36

6
English
Side Handle (Fig. B)
WARNING: To reduce the risk of personal injury, ALWAYS
operate the tool with the side handle properly installed.
Failure to do so may result in the side handle slipping
during tool operation and subsequent loss of control. Hold
tool with both hands to maximize control.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories.
An accidental
start-up can cause injury.
Active Vibration Control (AVC) System
For best vibration control, hold the tool as described in Proper
Hand Position and apply just enough pressure so the damping
device on the main handle is approximately mid stroke.
The active vibration control neutralises rebound vibration from
the hammer mechanism. Lowering hand and arm vibration,
it allows more comfortable use for longer periods of time and
extends the life of the unit.
The hammer only needs enough pressure to engage the active
vibraton control. Applying too much pressure will not make the
tool chip faster and active vibration control will not engage.
D
e
WALT Tool Tag Ready (Fig. A)
Optional Accessory
Your hammer comes with D
e
WALT tool tag mounting holes 9
and fasteners for installing a D
e
WALT Tool Tag. You will need a
T20 bit tip to install the tag. The D
e
WALT Tool Tag is designed
for tracking and locating professional power tools, equipment,
and machines using the
D
e
WALT Tool Connect™ app. For proper
installation of the D
e
WALT Tool Tag refer to the D
e
WALT Tool
Tag manual.
Electronic Speed and Impact Control (Fig. A)
The electronic speed and impact control allows optimal tool
control for precise chiseling.
To set the electronic speed and impact control dial
8
, turn the
dial to the desired level. The higher the number, the greater
the speed and impact energy. Dial settings make the tool
extremely flexible and adaptable for many different appli cations.
The required setting depends on the bit size and hardness of
material being chiseled.
• When chiselling soft, brittle materials or when minimum
break-out is required, set the dial to a low setting;
• When breaking harder materials, set the dial to a
high setting.
Description (Fig. A)
WARNING:
Never modify the power tool or any part of it.
Damage or personal injury could result.
1
ON/OFF rocker switch
2
Side handle
3
Front Barrel (Collar)
4
Mode selector dial
5 Main handle
6
Tool holder
7 Locking sleeve
8
Electronic speed and
impact control dial
9
D
e
WALT tool tag mounting
holes
10
Screw for side handle
mounting
11
Date code
Intended Use
Your chipping hammer has been designed for professional
chiseling and chipping applications.
DO nOT use under wet conditions or in the presence of
flammable liquids or gases.
Your chipping hammer is a professional power tool.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
•
Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
Date Code Position (Fig. A)
The date code
11
, which also includes the year of manufacture,
is printed into the housing.
Example:
2019 XX XX
Year of Manufacture
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
Wear ear protection.
Wear eye protection.
Package Contents
The package contains:
1 Chipping hammer
1 Side handle
1 Instruction manual
• Check for damage to the tool, parts or accessories which may
have occurred during transport.
• Take the time to thoroughly read and understand this manual
prior to operation.