Devine Onyx 6 User Manual Download Page 10

Specifications

General specifications for all models:

– lightweight speaker cabinet with plastic housing
– 6 or 8 inch speaker with woofer and compression driver and horn
– metal grille with acoustic foam inside
– acoustic foam behind grille to prevent any unwanted matter from getting inside the speaker
– grille covers the front of the speaker for optimal protection
– tweeter fitted with special horn design for optimal sound dispersion
– high-quality plastic housing with black finish
– rubber feet
– 70.7/100V functionality with various power-drain settings and bypass functionality for 8-Ohm use
– 35 mm stand flange with tightening knob for secure mounting on a speaker stand and optimal dispersion of
the high tones
- connections: 1x lockable speaker input, 1x lockable speaker output, wire terminals

Technical specifications per model:

Model

Onyx 6

Onyx 8

Frequency Range

72 Hz - 19 kHz

61 Hz - 19 kHz

Power Capacity (RMS / Peak)

in 8-Ohm mode

80 / 320 W

100 / 400 W

100V Tapping Values

70,7 V: 2,5W / 5W / 10W / 20W / 40W

100V: 5W / 10W / 20W / 40W

Maximum SPL

108 dB

111 dB

Low Frequency Speaker

6.5" woofer

8" woofer

High Frequency Speaker

1" compression driver

High Frequency Horn Dispersion

90° x 60° (H x V), a-symmetrical

Crossover Frequency

3.5 kHz

3.5 kHz

Dimensions

220 x 368 x 210 mm

275 x 492 x 270.5 mm

Weight Per Speaker

4.7kg

7.4 kg

The information in this user manual is subject to change at any time without notice.

Version: 1.0

Date of creation and author’s initials: 09-01-2020 RV Revision date and author’s initials: -

Summary of Contents for Onyx 6











Reviews: