RF EMISSIONS
This Class B digital apparatus complies with Canadian ICES-003.
Cet Appareil numérique de la classe B est conforme à la norme
NMB-003 du Canada.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
PRECAUTIONS
Do not attempt to disassemble the camera! There are no
user-serviceable parts inside. Refer servicing to qualified service
personnel.
Handle the camera with care. Improper handling or storage could
damage the camera.
Do not expose the camera to moisture, or try to operate it in wet areas.
Should the camera become wet,
immediately
turn power off and refer
servicing to qualified personnel.
Never face the camera towards the sun, even when not in use! Use
caution when operating the camera in the vicinity of spotlights or other
bright lights and light reflecting objects.
Do not operate the camera beyond its temperature, humidity or power
supply ratings. Use the camera under conditions where temperatures
are within –10°C to +50°C, and relative humidity is below 80% (non
condensing).
When the camera is not in use, ensure the lens is kept properly in place
to protect the CCD sensor.
Do not touch the CCD sensor directly with your fingers. If necessary,
use soft cloth moistened with alcohol to wipe off the dust.
2
Part
Descriptions
CONNECTION
Important Note:
Qualified service personnel or system installers should make the
installation. Ensure the power is OFF before handling the power cable,
no matter AC main power mode or low voltage AC24V/DC12V mode.
A.
Main Power Model (100VAC-240VAC 50Hz) :
1.
Connect the AC power cord (supplied as standard accessory) to the
power cord socket of the camera.
3
2.
Connect the AC power cord to an electrical outlet of AC100V ~ AC253V
50Hz/60Hz.
Notes:
z
Connect the power cord firmly. The power cord should be long
enough for panning and tilting. If the cable is too short, the power
cord plug may be pulled off the camera when the camera pans or
tilts.
z
Brown: Live, Reference line lock. Blue: Neutral.
z
This camera voltage could accept range rated is AC90V ~ AC260V.
But recommend range is AC100V ~ AC253V.
B.
Dual Power Model (12VDC/24VAC).
The series model has an AC/DC compatible input terminal. DC12V or
AC24V power supply cable can be connected to this terminal. The
camera detects the power source automatically.
Recommended wire gauge size.
Φ
0.65mm(AWG22), Stranded wire
0.32m
㎡
(AWG22), Element wire
φ
0.18Min.
1. 12V DC Power Supply
Connect the power cable to the AC/DC compatible input terminal on
the rear panel of the camera. +12VDC should connect is the RED
terminal. 0VDC to the white terminal. Black terminal for Earth
connection.
2. 24V AC Power Supply
Connect the power cable to the AC/DC compatible input terminal on
rear panel of the camera.
Notes:
z
If the cable is too short, the power cable may be pulled off the
camera when the camera pans or tilts.
z
Red: Live, Reference line lock, Black: GND,. White: Neutral.
z
Voltage range: Rated AC12V ~ AC28V. or DC10V ~ DC30V.
C.
Video Cable
Connection the coaxial cable with BNC female to BNC connecter on
the rear panel of camera. Measure set the termination switch to the
75
Ω
position on the last monitor, and to the Hi-Z position on the other
monitors. Do not change the positions after setting.
D.
Audio Connection
Connection the audio signal through the RCA connector to the rear
panel of camera.
E.
RJ-11 Easy Caballing Connection
Refer below picture of the pin assign to connect 6pin multi flat cable for
system connections. While caballing, the impedances of cable must
be considering, It is recommend minimum of power input must higher
then 15VDC with 3000cm/100ft cable.
4
Vari-Focal Lens.
Microphone.
Power Socket,
100VAC - 250VAC Power Input
LED
Power Indication
Terminal Block,
24VAC/12VDC Power Input
RCA Connecter,
Audio Output
RJ-11 Connecter
BNC, Video Output
Bracket Mounting Screw
Hole. 1 / 4", 7mm deep.
Vari-Focal Lens Cover.
Cover For DIP Switch and
Function Adjust.
1. NC
2, DC Power input
3, NC
4, Video Output
5, Audio Output
6, GND
3000cm / 100ft approx.
6pin Multi-flat cable
