background image

E-1

INSTALLATION MANUAL

A10D-9550-03

SD-509 

Saddle Stitcher

Caution:

Lifting the machine in an awkward position or 
transporting it in a poorly balanced position could 
result in personal injury. When transporting the 
machine, assign an adequate number of persons 
to the job and ensure that each person can take a 
good position of not being excessively loaded.
(mass: approx. 24 kg (52-15/16))

I. Accessory parts

Note:

This manual provides the illustrations of the acces-
sory parts and machine that may be slightly different 
in shape from yours. In that case, instead of the 
illustrations, use the appearance of your machine to 
follow the installation procedure. This does not 
cause any significant change or problem with the 
procedure.

No.

Name

Shape

Q’ty

1. Saddle unit

1

2. Exit tray

1

3. Exit tray cover

1

4. Rail (Right)

without hook

1

5. Rail (Left)

with hooks

1

A10DIXC001DA

A10DIXC002DA

A10DIXC003DA

A10DIXC005DA

A11RIXC005DA

6. Label

1

7. Screw A 

(4 × 4 mm)

6

8. Screw B 

(3 × 6 mm)

1

9. Screw C 

(4 × 9 mm)

1

10. Screw D 

(3 × 8 mm)

3

11. Screw E 

(3 × 8 mm)

1

12. Installation 

manual

1

set

After unpacking, be sure to get rid of the 
packaging materials and keep them out of 
the reach of children.
Putting the head in the plastic bag 
involves danger of suffocation.

No.

Name

Shape

Q’ty

9654

4040IXC046DA

A092IXC012DA

9735

9738

4980IXC019DA

II. Installation procedures

Note:

When mounting the saddle stitcher, mount it 
before mounting the finisher to the machine.

1. Turn off the machine and unplug the power cord 

from the power outlet.

2. Remove the saddle unit and all other accessories 

from the shipping carton and remove the protec-
tive tapes and protective materials.

3. If the finisher is mounted on the machine, remove 

the finisher.

Note:

For the finisher removal procedure, see installa-
tion manual for finisher.

4. Open the front door of the finisher.
5. Remove the plate from the finisher as shown 

below (four screws).

6. Remove the front cover of the finisher (three 

screws).

A10DIXC008DB

A10DIXC006DA

A10DIXC007DA

A10DIXC009DB

A10DIXC010DB

Applied Machine: FS-527

Summary of Contents for SD-509







Reviews: