Devantech ESP32LR20 User Manual Download Page 8

Page: 8 / 15

ESP32LR20

User Manual v1.02

TCP/IP Commands.

The ESP32LR20 has a built in TCP/IP command set which allows you to control the module

remotely.
All commands are sent using plain ASCII text. PuTTY is a good cross platform terminal program to

use for testing. The TCP/IP port is the one you set-up with the PA command during USB
configuration. Do not use port 80 as that is reserved for the HTML commands and Webpage.

SR Set Relay.

This is used to turn a relay on or off

To turn Relay 1 on:

SR 1 1

The first number is the relay number from 1 to 2.
The second number is 1 or 0, on or off.

So turn turn relay 1 off again:
SR 1 0

The command will respond with ok or fail.

SR 1 1

SR 1 6
fail

< 6 is not valid, only 1 or 0 for on/off

SR 9 1

fail

< relay 9 does not exist.

GR Get Relay.

Will return the state of the relay.

To get the status of relay 2:
GR 2

GR 2
0

GR 9

fail

< relay 9 does not exist.

Devantech Ltd.

www.robot-electronics.co.uk

Summary of Contents for ESP32LR20












Search results

Summary of Contents for ESP32LR20

Reviews:

Devantech ESP32LR20, User Manual, Page: 8 / 15

Search results

Summary of Contents for ESP32LR20

Reviews: