manualshive.com logo in svg

DEVA DB910, Instruction Manual, Page: 19 / 43

Share
Download
DEVA DB910 Instruction Manual Download Page 19

65 Aleksandar Stamboliyski Str., 8000 Bourgas, Bulgaria

Tel: +359 56 820027, Fax: +359 56 836700

E-mail: [email protected] ,Web: www.devabroadcast.com

- 19 -

WEB Interface Menu pages

STATUS

Upon opening the WEB interface, the main Status window will appear. The page contains 

information on the device’s current status - the LED bar-graph representation of the audio sources’ 

audio levels. The interactive buttons placed over the LED bar-graphs allow the audio source to be 

manually changed. 

IMPORTANT NOTE:

 When the DB910 works in [Auto] mode the Backup option is working 

as per the set priority in the relevant section. If the source is manually changed, or Dayparting is 

activated, the Backup option will be deactivated, and only the selected audio source will be used. 

Meaning that in case of audio loss, the DB910 will not switch to a backup source.

At the top of the control window is placed a constant section, containing information about the 

input in use, Date/Time, Uptime and session timeout. 

At the bottom of the control window is an information bar, gathering all the important connection 

parameters – firmware version in use, serial number, IP Address, and etc.

Upon change of the Web Interface screens, the main status window will resize automatically 

and become a constant part of each tab. Thus, allowing reading at a glance of all the mandatory 

parameters.

 

Summary of Contents for DB910












































Reviews:

No comments