Dettson C105-2-V Installation Instructions And Homeowner'S Manual Download | Manualshive

Page: 34 / 38

background image

11

FURNACE SPECIFICATION

Furnace model: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial number: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Furnace orientation: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel (N.gas/propane): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Conversion kit number: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inlet gas pressure: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Outlet gas pressure high fire (100%): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Outlet gas pressure low fire (70%): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Static pressure in return: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Static pressure in supply: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Temperature rise: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Is drain trap filled with water?: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Is drain trap outlet vented with a Tee?: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Are condensate tubing properly slopped towards drain trap?: . . . . . . . .
Furnace leveled or slopped?: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Venting pipe diameter: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Venting length: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Venting termination: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

33

«
...
32
33
34
35
36
...
»

Summary of Contents for C105-2-V







































Reviews:

No comments

Related manuals for C105-2-V

Brand: Heat Controller Pages: 10

Brand: American Standard Pages: 24

Brand: Goodman Pages: 12

Brand: Suburban Pages: 40

Brand: Napoleon Pages: 44

Brand: Daikin Pages: 82

Brand: Carrier Pages: 76

Brand: Carrier Pages: 74

Brand: Carrier Pages: 86

Brand: United States Stove Pages: 20

Brand: Unitary products group Pages: 8

Brand: Allied Pages: 36

Brand: Allied Pages: 46

Brand: Allied Pages: 55

Brand: Allied Pages: 59

Brand: Allied Pages: 57

Brand: Allied Pages: 60

Brand: barbas Pages: 104

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands